Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across North Richland Hills
Gate parts and welding in North Richland Hills usually comes down to one of two situations: a hinge or post that has failed after decades of Tarrant County clay movement, or a homeowner who wants an opener added to a gate that was never built for one. We handle both, and we do the welding on site so your gate never leaves your driveway. Hal Gatewood has been fixing gates since 2001, and our crew knows the older HOA subdivisions on the west side of North Richland Hills better than most people know their own backyards. If your gate is dragging, seizing, or cracked at a weld point, call (817) 241-4067 and a live person picks up.
Why Gatewood Fence & Gate Is North Richland Hills’s Preferred Gate Parts & Welding Company
The name is on the shop, and the shop is down the road. That is the oldest accountability there is, and it is how we have worked in North Richland Hills for a long time. We are not a franchise with a call center three states away. Hal Gatewood owns the company, his address is published, and his license number is something anyone can look up. When you call about a sagging gate near the Richland Hills border or a frozen slide mechanism off Rufe Snow Drive, the person who answers is the person who can actually help you.
We get called to North Richland Hills after other companies have already been out once or twice. That is not a coincidence. The clay soil under NRH heaves hinge posts out of plumb, and a gate that sags in the hinge post, not in the middle, keeps sagging until someone fixes the post itself. We fix the post. Our 90-Day Done Right Promise is stamped in writing on every job. If it is not done right, we make it right. No runaround, no fine print, no hedge language. Just Hal’s word.
You also get a live person on the phone 24 hours a day, seven days a week. Not a voicemail, not a bot. That matters at 9 p.m. when your gate will not close and your dog is eyeing the gap. We answer, and we get someone to North Richland Hills fast.
Our Gate Parts & Welding Services in North Richland Hills
This is the work we do most often in North Richland Hills, and we do it with a repair-first mindset. If a part can be welded, braced, or realigned, we are not going to sell you a new gate. That is the whole point of our Gate Parts & Welding service.
Hinge Replacement
Original steel hinges on 1980s and 1990s ornamental iron gates across North Richland Hills have been through 30-plus years of North Texas humidity. They corrode, they seize, and they let the gate drop far enough to drag on the driveway. We cut out the old hinges, weld in new ones rated for the gate’s weight, and realign the gate so it swings square. Fix the hinge without checking the post and you will fix it twice. We check the post.
Post Replacement
A gate sags in the hinge post, not in the middle. Under North Richland Hills, the expansive black clay shrinks during summer droughts and swells with fall and spring rains. That cycle tilts gate posts a little more every year. We set new posts in deeper concrete piers with proper footings, often welding a steel post to replace a rotted or tilted wooden one. This is structural work, and it has to be done before any hinge or weld repair will hold.
Rail Repair
Top and bottom rails on ornamental iron gates crack where they meet the stiles. Sometimes it is decades of wind load, sometimes it is the February 2021-style ice events that snap brittle steel. We weld the crack, grind it smooth, and match the finish so an HOA architectural committee will not flag it. In North Richland Hills, finish match is not optional. The management company checks.
Custom Welding
Not every repair fits a catalog part. We fabricate brackets, extend posts, reinforce frames, and build custom hinge plates for gates that were installed before residential automation was common. If your 1990s manual swing gate needs bracing before a LiftMaster or Ghost Controls opener goes on, that is custom welding, and we do it on site in your driveway.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in North Richland Hills
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. In North Richland Hills, we commonly work on LiftMaster and Ghost Controls openers added to older iron gates, and Linear operators on HOA shared entry systems. Because we stock common parts locally, we can often complete a hinge or weld repair in one trip without waiting on a shipped component. If you have a Viking or DoorKing opener and the gate frame needs welding before the operator can be remounted, that is exactly the kind of job we take.
Common Gate Parts & Welding Problems We See in North Richland Hills Homes
- HOA-approved 1980s-90s iron gates with corroded original hinges. The western sections of NRH near Richland Hills have the most worn gate infrastructure. Original steel hinges corrode from decades of humidity, and the gate drags or seizes after the hinge post shifts in the clay. We replace hinges and set the post back to plumb in the same visit.
- Adding an operator to a pre-automation manual swing gate. North Richland Hills has hundreds of 1990s ornamental iron driveway gates that were installed before residential automation was common. The original frames and posts were not engineered for motor torque. Without post reinforcement and frame bracing, the weld points crack and the safety edge trips constantly. We brace first, then mount the operator.
- Ice-event weld cracks and seized slide mechanisms. The February 2021 freeze and similar storms crack weld points on iron gates across North Richland Hills. Rack and pinion slide gates seize when the rack shifts or the gate frame twists slightly. Weld repair and realignment get the gate moving again.
- Shrink-swell clay heaving hinge posts seasonally. North Texas clay contracts in drought and expands after rain. On some NRH properties, the same gate post tilts noticeably every few years. A deeper footing and a welded steel post stop the cycle for good, rather than just for the season.
Pricing for Gate Parts & Welding in North Richland Hills, TX
Here are honest ranges for the work we do in North Richland Hills. Hinge replacement on a standard ornamental iron driveway gate typically runs $180 to $340, including welding and realignment. Post replacement with a new concrete footing runs $400 to $800 depending on depth and whether we are setting steel or wood. Rail repair and crack welding run $150 to $400, depending on how many weld points need attention and whether finish matching is required. Custom welding for frame bracing before an operator mount runs $300 to $600.
What moves the price is access, finish matching, and whether the post footing has failed or just shifted. We quote the price before any work starts, and the number we give you is the number on the invoice. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Call (817) 241-4067 for an exact quote. Estimates are free.
We Also Serve Cities Near North Richland Hills
Our Gate Parts & Welding in North Richland Hills crew also runs calls to Hurst, Bedford, Colleyville, and Fort Worth. If you live in one of those cities and your gate has a cracked weld or a leaning post, the same repair-first approach applies. Same phone, same promise.
Serving North Richland Hills, TX - Our Local Coverage Area
We’re based in the North Richland Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in North Richland Hills
Yes, most HOA communities in North Richland Hills require architectural approval before any structural gate work, including hinge post replacement, frame welding, or finish changes. We have worked with NRH management companies long enough to know how to specify a repair that passes the finish check the first time. We will tell you exactly what to submit, and we can often write the repair description in the language the committee expects. Call (817) 241-4067 and we will walk you through it.
Because the hinge post is moving, not just the hinge. The expansive Tarrant County black clay under North Richland Hills shrinks during drought and swells after rain, tilting the post a little more every cycle. A new hinge on a tilted post fails within months. We fix the post first, then weld in the hinge. That is the repair that holds.
Usually, yes. The gate needs a structural assessment first. Original 1990s ornamental iron frames were not built for motor torque, and the hinge posts have often shifted in the clay. We reinforce the post with a deeper footing, brace the frame, and then mount the operator. You keep the gate you have, and the opener runs without tripping the safety edge every cycle. Call (817) 241-4067 for a free measure and a written price.
Automated gates require entrapment protection: safety edges, photocells, or both, depending on the gate type and the operator. This is not optional, and it is not a corner we cut. We install the correct safety devices for your specific gate and operator combination, and we test them before we leave. If you are adding an opener to an older manual gate in NRH, the safety hardware is part of the quote.
It determines everything. A new post set in a shallow footing will shift again within a few wet-dry cycles. We set posts in deeper concrete piers than the original builders used, often with a welded steel post instead of wood. That is the difference between a repair that lasts three years and one that lasts twenty. In North Richland Hills, the soil is the reason the old gate failed, so we build the new footing for the soil we actually have.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving North Richland Hills with gate repair and welding since 2001.