FAAC Gate Repair Nationwide | Gatewood Fence & Gate

FAAC Gate Repair in North Richland Hills: What to Know First

We provide independent FAAC gate repair in North Richland Hills, and most jobs are done in one visit, often the same day you call. A typical FAAC repair runs between $225 and $495, depending on what failed, and you’ll know the price before any work starts because we quote it upfront and stick to it. If your FAAC gate motor is humming but not moving, or the gate opens halfway and reverses, call Hal at Gatewood Fence & Gate: (817) 241-4067.

Call (817) 241-4067

This page is for homeowners in North Richland Hills who own a FAAC gate operator or a FAAC hydraulic swing gate system and need someone who actually understands how these European machines behave in Texas heat and clay soil. As an independent FAAC service provider, we’re not tied to the manufacturer’s sales targets. We’re tied to fixing your gate right the first time.

How FAAC Products Fail - and How We Fix Them

FAAC builds good equipment, but North Richland Hills throws a few curveballs at it that you won’t read about in the owner’s manual. Here’s what we actually see:

• Oil leaks on FAAC 390 and 391 hydraulic operators. These are the workhorse hydraulic swing gate operators around North Richland Hills. After four or five Texas summers, the shaft seals dry out and start weeping fluid. The gate gets sluggish, then stops mid-cycle. The fix is a seal kit and fresh FAAC hydraulic oil, not a new operator. We do this repair on-site. We’ve seen national companies quote a full replacement for what was a $30 seal and an hour of work.
• Capacitor death on FAAC 402 and 412 control boards. When the gate hums but won’t move, that’s usually a failed start capacitor on the operator, especially on lots in the Home Town or Smithfield corridor where afternoon heat sits on the motor housing. We replace the capacitor and check the board’s relay contacts while we’re in there, because a weak capacitor often overloads the relays over time.
• Limit switch drift on C720 and S800 slide operators. North Richland Hills sits on expansive clay. When the ground moves through a wet spring, the gate post shifts a fraction of an inch, and the limit switch that was perfectly adjusted in October is now out by an inch. The gate slams against the stop or stops three inches short. We re-set the limits and, if the post has moved enough, we’ll talk to you about the real fix: stabilizing the post rather than band-aiding the switch.
• Photocell alignment failures on nearly every FAAC model we service. The sun angle in North Richland Hills plays tricks on infrared sensors, especially on west-facing gates in the late afternoon. A gate that reverses for no reason is often just a photocell that’s drifted or gotten a layer of dust on the lens. We clean, realign, and shim the mount so it stays put. It’s a ten-minute fix that a lot of companies turn into a $400 board replacement. We don’t.
• Gearbox wear on high-cycle FAAC 400 series operators in HOA communities. When a gate cycles forty or fifty times a day - which is normal for a small subdivision entrance off Rufe Snow - the bronze gear wears past tolerance in about five to seven years. The operator still runs but sounds like a coffee grinder. We replace the gear set, re-lubricate with the correct FAAC-spec grease, and test the load. Half the cost of a new operator, and your gate sounds right again.

Our FAAC Gate Repair Process

When you call Gatewood Fence & Gate, here’s how a FAAC repair actually goes:

1. 1
   You talk to a person. Not a voicemail, not a menu. Hal or one of his crew answers. You describe what the gate’s doing. We ask a few questions about the model and what happens when you press the remote.
2. 2
   We show up when we said we would. Hal grew up off Smithfield Road and still lives in North Richland Hills, so he knows which streets flood and which ones back up at school pickup. He plans for it.
3. 3
   We diagnose on-site. We open the operator cover, test voltage, check the control board, and look at the physical hardware. We don’t guess from the truck. We find the actual fault before we quote anything.
4. 4
   You get a price before any part is ordered or any bolt is turned. We use OEM FAAC parts when the repair is under any active warranty or when the part matters for safety. We use quality aftermarket equivalents when they’re genuinely as good and save you money. We tell you which is which and why.
5. 5
   We fix it, test it, and clean up. We cycle the gate ten times minimum, verify the safety edges and photocells work, and leave your driveway cleaner than we found it. Then we hand you the written 90-Day Done Right Promise with Hal’s name on it.

What FAAC Gate Repair Costs in North Richland Hills

The cost of FAAC gate repair in North Richland Hills depends on what failed, but here’s what we typically see. A capacitor or limit switch replacement runs $225 to $320. A hydraulic seal kit on a FAAC 390 or 391 generally lands between $310 and $420 including fluid and labor. Gear set replacement on a 400 series operator runs $380 to $520. A full control board replacement, when the board is genuinely dead, sits between $450 and $800 depending on the model and whether we go OEM or aftermarket. What moves the price most is cycle count, the age of the operator, and whether previous repairs left the internal wiring in readable shape. We’ll give you the exact number before we start, and it won’t change when we hand you the invoice. Call (817) 241-4067 and we’ll come quote it free, with no trip charge anywhere inside Tarrant County.

Why North Richland Hills Homeowners Call Gatewood Fence & Gate for FAAC Work

You can find a gate company that will quote you a new FAAC operator over the phone without ever looking at the existing one. That’s not us. Hal Gatewood has been repairing gates in North Richland Hills since 2001, and he still fixes more than he replaces because most FAAC hardware has plenty of life left in it if you address the actual fault. Every job gets the 90-Day Done Right Promise in writing: if it’s not right, one call brings Hal back. No runaround, no “we’ll see.” And if your FAAC gate is beyond saving, we service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing too, so you’ll get an honest recommendation on what your next operator should be, not just what the salesman’s spiff is on this quarter. We’ve been here 29 years, and our license number and shop address are published. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.

FAQs

Get Your FAAC Gate Fixed Right

If your FAAC gate is acting up in North Richland Hills, call Hal Gatewood at (817) 241-4067. You’ll talk to a person who knows FAAC equipment, who grew up here, and who will show up when he says he will. We’ll diagnose the actual problem, quote you a fair price, fix it right, and stand behind it for 90 days in writing. Don’t wait until the gate sticks open and the dog makes a run for Davis Boulevard. Call today and let’s get it working again.

Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving North Richland Hills and nearby areas.