FAAC Gate Installation Nationwide | Gatewood Fence & Gate

FAAC Gate Installation in North Richland Hills: What to Know First

We’re an independent FAAC service provider in North Richland Hills, and we install, wire, and commission FAAC gate systems the way they should have been done the first time. Most FAAC gate installations in our area take a day for a single swing gate and up to three for a double gate with new posts, and you’ll know the price before we turn a wrench. If you own a FAAC opener that a previous installer left half-done, or you’re replacing a gate and want the FAAC hardware mounted right, call (817) 241-4067 and talk to a live person at Gatewood Fence & Gate.

Call (817) 241-4067

This page is for North Richland Hills homeowners who already have FAAC equipment or are considering it. We service the whole FAAC lineup that shows up in local driveways: the C720, C721, the 400 series, the 844 and 770 hydraulic operators, and the newer FAAC E024U control boards. Hal Gatewood has been working on these systems since 2001, and most of what we fix is not the motor itself but the installation around it.

How FAAC Products Fail, and How We Fix Them

FAAC builds good equipment. What fails in North Richland Hills is usually the installation, the adjustment, or a part that was never right for the job. Here’s what we see:

• C720/C721 slow creep or dead stop: The C720 and C721 are the most common FAAC swing operators in North Richland Hills, and the number one reason they stop working is the capacitor. It’s a $25 part, but the symptom looks like a dead motor. A homeowner calls thinking they need a new operator. We test the capacitor on site, replace it if it’s weak, and save them $900. Some installers never check it before quoting a full replacement.
• 844 or 770 overheating on a heavy gate: FAAC hydraulic operators like the 844 and 770 are workhorses, but when someone hangs a 600-pound gate on an operator rated for 400, the hydraulic fluid cooks. The gate slows down over a few weeks, then trips the thermal overload. We tell owners the truth: either reduce the gate weight with a different panel or upgrade the operator. We won’t just bump the pressure relief and call it done, because that’s how you blow a seal and lose a gate mid-swing.
• E024U board with no power, blinking red: The E024U control board is picky about voltage. When a gate installer taps into the nearest outlet instead of running a dedicated line, the board sees voltage drop and errors out. Hal’s team fixes this by running the proper circuit, not by resetting the board and hoping. If your board is dead, we can source the OEM E024U or a known-good compatible board, wired clean.
• Swing gate wing sag on FAAC 400-series operators: The 400 series uses an articulated arm, and when the gate’s hinge post leans, the arm binds. The gate grinds, the operator fights it, and a bracket cracks. We weld a reinforcement plate and straighten the post before remounting the arm. Most installers replace the arm and walk away. The post lean is still there. You’ll be calling someone else in six months.
• FAAC gate won’t close all the way, then reverses: On a sliding gate, that’s usually a worn guide wheel or a misaligned rack. On a swing gate, it’s the limit switch or a bad photo eye alignment. FAAC systems are sensitive to obstruction detection. A leaf blowing across the beam will stop the gate. We adjust the sensitivity and beam height for local conditions in North Richland Hills, where wind and debris are part of every spring afternoon.

Our FAAC Gate Installation Process

Here’s how a FAAC gate installation goes when Gatewood Fence & Gate shows up:

1. 1
   Call and talk to a person. You call (817) 241-4067 and describe your gate. A live person answers, 24/7. We schedule a time, and we show up in that window.
2. 2
   Site inspection and measurement. We measure the gate, check the posts with a level, and look at the power source. If it’s a FAAC opener going on an existing gate, we verify the gate weight against the operator’s rating before anything is ordered or installed.
3. 3
   Straight answer on parts. We tell you whether the job needs OEM FAAC parts or a quality aftermarket part that matches the spec. For boards and arms, we recommend OEM when the gate is under warranty. For capacitors, limit switches, and photo eyes, aftermarket parts from proven suppliers work fine and cost less. We never use a part that’s not rated for your specific FAAC model.
4. 4
   Installation, done in your driveway. We mount the operator, run the wiring, and weld reinforcements on site if the hinge post needs it. Your gate stays in your driveway, not on a trailer headed to some shop.
5. 5
   Testing and adjustment. We cycle the gate 20 times or more, adjust the force and limits, and test every safety sensor. If it’s a sliding gate, we check the rack engagement and guide wheels. If it’s a swing gate, we check for bind and drift.
6. 6
   Cleanup and the promise. We clean the work area and write the 90-Day Done Right Promise on your invoice. If something’s not right, you call and Hal comes back. That’s it.

What FAAC Gate Installation Costs in North Richland Hills

Here are realistic price ranges for FAAC gate installation in North Richland Hills, based on what we’ve quoted and completed in the past few years:

• FAAC C720 or C721 swing operator installed on an existing single gate: $1,800 to $3,200, depending on the control board, arm style, and whether we need to run new conduit.
• FAAC 844 or 770 hydraulic operator, double gate: $3,800 to $6,500. This is a heavier, more labor-intensive install, and the price moves with gate weight and post condition.
• New pedestal-style FAAC gate with operator, single driveway: $5,500 to $9,000 including the steel frame, panel, and full wiring. Custom designs and heavier gauge steel push that higher.
• Slide gate with FAAC rack and motor, single lane: $6,000 to $11,000 installed, again depending on gate length and existing concrete work.

What moves the price is post condition, power access, and whether we’re replacing a failed operator or starting fresh. You’ll get the exact number in writing before we start. No trip charge inside the county, and estimates are free. Call (817) 241-4067 and we’ll give you a straight number.

Why North Richland Hills Homeowners Call Gatewood Fence & Gate for FAAC Work

Hal Gatewood grew up off Smithfield Road and has been fixing gates in North Richland Hills since 2001. His name is on the shop, and the shop has a published address. When a FAAC system fails, you’re not calling a national number. You’re calling a local guy who drives past your neighborhood on his way to work.

Every FAAC job carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right, no runaround. We’re certified to service nine gate brands, so if your FAAC system is beyond saving or you want to compare, we can quote you honestly on LiftMaster, Mighty Mule, Ghost Controls, or DoorKing. We’ll tell you which one makes sense for your gate. And if you’re a senior or veteran, you get a permanent 10% discount on our labor. That’s not a promotion. That’s how we’ve always done it.

FAQs