Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Access Control Installation: The North Richland Hills Owner’s Guide
FAAC access control installation in North Richland Hills typically runs $850 to $1,900 installed, depending on whether you need a keypad, card reader, intercom, or a full phone-based entry system tied to your FAAC swing or slide gate operator. We stock the common FAAC-compatible keypads, receivers, and control boards on the truck, so most jobs are done same-day or next-day. Owners usually discover the problem the hard way: a keypad that stopped beeping after a storm, a remote that worked yesterday and won’t today, or a gate that opens fine from inside but won’t respond at the street. If your FAAC gate stopped listening to its access control, you’re in the right place.
Key Takeaways
- We install and repair FAAC access control systems across North Richland Hills, no subcontractor referrals.
- Installed pricing is quoted and agreed before work starts. No surprises when the invoice lands.
- We’re an independent gate shop. We’re not affiliated with FAAC, but we service their gear daily.
- Six of the nine gate brands we service are on a truck near you right now, including FAAC, LiftMaster, Mighty Mule, and Ghost Controls.
Which FAAC Models This Applies To
FAAC access control covers the keypads, card readers, intercoms, and RF receivers that tell a FAAC operator what to do. The most common units we install on FAAC swing and slide operators around North Richland Hills are the FAAC XKP keypad, the RP receivers, and the older Decoder boards (models like the 415 and the 455D). If you have a FAAC 400, 402, 4000, 415, 412, E145, S450H, or a 770 operator, the access control wiring and receiver logic are nearly identical across the board. Here’s the gotcha most homeowners never hear: FAAC 24-volt systems and FAAC 115-volt systems do not swap parts cleanly. The 400 series runs on 24V logic, while the older 750 and 760 operators lean on 115V relays. If you bolt a 24V keypad onto a 115V relay board, you’ll fry it in a week. We check the transformer first, every single time.
On the OEM-versus-aftermarket question, our honest take is this: FAAC’s own keypads and receivers are well-built, and we happily install them. But when a FAAC receiver dies on a 15-year-old operator, we often recommend a quality aftermarket equivalent from brands we trust and stock. Why? Because FAAC’s newer RF receivers sometimes require a matching encoder that won’t talk to your older FAAC motor smoothly. A good aftermarket receiver and remote kit gets you the same range and the same security at about two-thirds the price. Hal Gatewood has been matching FAAC parts to the right FAAC operator in North Richland Hills since 2001, and we’d rather sell you the part that works than the part FAAC’s catalog pushes.
Signs Your FAAC Access Control Installation Is Failing
- Keypad beeps but the gate won’t move. The relay on the keypad’s control board is sticking or has failed. We see this on FAAC XKP keypads after six to eight years of Texas heat and humidity. The keypad thinks it’s sending a signal, and the operator never hears it.
- Remote works from ten feet but not from the street. Your FAAC receiver’s antenna trimmer has drifted or the receiver itself is wearing out. FAAC RP receivers are generally good for ten years, but North Richland Hills sun beating on a metal post shortens that to about seven.
- Gate opens on its own at random times. That’s a receiver picking up interference from a neighbor’s opener or a failing relay chattering. It’s not a ghost. It’s almost always a receiver that needs replacing or a control board that’s tired.
- You need to punch the code three times before the gate responds. The keypad’s membrane contacts are wearing out. We can clean and re-seat them, but once moisture has worked its way in, replacement is the honest fix. In North Richland Hills, we get enough heavy dew and spring rain that this shows up every March like clockwork.
- Intercom audio crackles and dies halfway through a conversation. That’s usually a corroded wire at the keypad or a failing 24V power supply feeding the intercom. If the wire insulation is cracked and green at the connections, we replace the wire, not just the audio board.
Replacement Cost & What’s Included
Here’s what FAAC access control installation costs in North Richland Hills, honestly priced. A FAAC-compatible keypad installed runs $450 to $750, including the keypad, mounting hardware, wiring to the operator, and programming. A new receiver and two remotes runs $385 to $650 installed. A full phone-based or card reader system with keypad back-up runs $1,200 to $1,900, depending on how far the wire has to run from the house and whether we need to add an antenna. Every quote includes the part, our labor, wiring, weather sealing, and testing. We don’t do “parts extra” games.
What drives the range is mostly the wire run and the age of your existing operator. A 100-foot wire pull through a flowerbed costs more than a 20-foot run along a fence line. And if your FAAC operator is old enough that the control board is no longer available, we’ll tell you before we touch anything. The 90-Day Done Right Promise covers our entire access control installation in writing. If it’s not working right within 90 days, call (817) 241-4067 and we come back out. No runaround, no “well, actually.”
DIY or Call Us?
You can safely check a few things yourself. Is the circuit breaker for the FAAC operator still on? If you have a keypad that’s totally dead, check the GFCI outlet the operator’s plugged into, if it has one. Look for obvious water damage at the keypad edge or a cracked housing. Beyond that, access control work means working inside the operator with live 24V or 115V terminals, and that’s where a homeowner can get hurt or make a $200 problem into a $600 problem. You’re not being chicken by calling us. You’re being smart with a system that’s wired to your house.
If you’ve already bought the part and want someone honest to install it, we’ll do that too. We’ll inspect it for compatibility before we spin any wire. Call (817) 241-4067 and tell us what you have. We’ll tell you if it fits before you pay us a dime.
FAQs
About six to eight years outdoors, though Texas sun and humidity can shorten that on west-facing brick or unshaded metal posts. If your FAAC keypad is five years old and acting up, a replacement is the better money than a repair.
Sometimes we can. Bent relay contacts, corroded wire terminals, and cold solder joints on older FAAC Decoder boards can be cleaned and re-soldered at the bench. If the board’s processor is dead, we’ll tell you that too. We repair-first, but we won’t rebuild a board that’ll fail again in six months.
A keypad or receiver swap takes us one to two hours on site. A full phone-based system with a new card reader, antenna, and wiring can take four to six hours. We’ll give you a straight time window before we start, and the person who shows up is the person who does the work.
We stock FAAC-compatible keypads, receivers, and wire on our trucks around North Richland Hills, so we can often fix it the day you call. If it’s an oddball FAAC board from a discontinued series, we can usually have it in two to three business days. Call (817) 241-4067 with your operator’s model number and we’ll check the bench before we roll.
If your FAAC access control has been dead for a week and you’re tired of getting out of the truck to open the gate by hand, call us. We answer the phone around the clock in North Richland Hills. We’ll quote you a real number before we show up, and the price is the price. If I hand you my number, use it – that’s what it’s there for.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving North Richland Hills and nearby areas.