Linear Access Control Installation Nationwide | Gatewood Fence & Gate

Linear Access Control Installation: The North Richland Hills Owner’s Guide

We stock and install Linear-compatible access control parts across North Richland Hills, with most keypads, receivers, and entry systems installed between $385 and $780. We carry the common Linear parts on the truck, so if your system matches what we stock, we can often handle it same day. If you’re reading this, you likely have a Linear keypad that’s gone blank, a receiver that stopped triggering the board, or a phone entry system that suddenly quit ringing your house line. The gate still moves, but the access control half of the system is dead, and every visitor now stands there pressing buttons like it’s a broken vending machine.

Call (817) 241-4067

Here’s what most North Richland Hills folks actually need to know: Linear access control failures usually come down to the keypad membrane, the receiver board, or weather-damaged wiring between the entry device and the operator. Rarely do you need to replace everything. And this is the part where a repair-first shop can save you hundreds compared to whoever sold you the system originally and now wants to sell you a new one.

Which Linear Models This Applies To

Linear made access control components under several model families that show up consistently on North Richland Hills gates. You’ll see them mostly as part of an older gate install or one retrofitted by a previous owner: the AE-100, AE-500, and AE-1000 telephone entry systems, the AM-KP and AM-KPR keypads, the DVS and DT series receivers, and the older MegaCode single-channel receivers paired with a visor transmitter. If you have a Linear operator, the model number is normally on a silver label inside the control box, usually mounted on the gate post or just beneath the motor housing. Look for a line reading something like “LRA” or “LS” or “AP”. If the box was replaced at any point, the label may be gone or faded, and that’s fine: we can identify the board wiring in about five minutes when we’re on site.

One thing to know before you order anything online: Linear’s receivers run on either the older DIP-switch scheme or the newer MegaCode rolling-code platform, and they don’t talk to each other. We’ve watched people buy a MegaCode keypad to replace a DIP-switch receiver, then spend three weekends wondering why it won’t sync. If you’re unsure which generation you have, call us before you spend money on a part that doesn’t match the board. For Linear specifically, we prefer OEM boards and remotes, because aftermarket Linear knockoffs tend to have fast-burning displays and cheap membranes that crack in the Texas heat by year two. We’ll install aftermarket if you ask us to, but we’ll tell you honestly what you’re buying first.

We also stock and install parts for LiftMaster, Mighty Mule, and Ghost Controls, so if your access control setup is a joint effort from a couple of different brands, we can sort it out without making three trips.

Signs Your Linear Access Control Installation Is Failing

• Keypad lights up but won’t open the gate. The membrane is often fine, but the contacts underneath are worn, or the receiver has lost a programming memory line. Linear keypads that sit in direct sun along the Davis Boulevard corridor eat membranes in three to four years; it’s a known failure point, not a one-off flaw.
• Gate opens the first time, too high the second time, not at all the third. That’s the classic picture of a receiver dropping its learned transmitter codes. Usually the board’s memory buffer is full, or the antenna is gathering water at the connection point. We see it every spring after the North Richland Hills rainy season.
• Phone entry rings once then quits. The AE-series entry box is trying to call out but the phone line converter inside is dying. In newer installs this happens when the box was wired for a landline that no longer exists; people switched to VoIP without reconfiguring the panel, and now the system’s trying to dial a dead number.
• The keypad or entry box has gone completely dark. That’s a power supply problem about 80 percent of the time: a fused transformer, a popped breaker at the operator, or melted low-voltage leads where someone ran the wire too close to a heat source. The remaining 20 percent is a fried board.
• Multiple remotes stopped working at once. One dead remote means a bad remote. All of them dead points to the receiver or the operator’s main control board not passing signal. We carry a test transmitter on the truck so we can tell the two apart in about ninety seconds.

Replacement Cost & What’s Included

In North Richland Hills, you can expect to pay around $385 to $780 installed for a Linear access control replacement, depending on which part died and how much rewiring the job needs. A keypad replacement alone sits at the lower end. A new MegaCode receiver plus a reprogrammed remote set runs in the middle. A full AE-series telephone entry system replacement, with new wiring from the post to the operator, lands at the higher end. Parts and labor are quoted as one number, and that number doesn’t change at the door. We write it down, you agree to it, then the work starts. The old part gets pulled and the new part is buttoned up, tested at the gate, and reprogrammed to your existing remotes when the system allows. Every job carries our 90-Day Done Right Promise in writing: if the part we installed fails in that window, we make it right, no runaround and no invoice.

You also get the standing offers that apply to every repair: $40 off any repair over $200, no trip charge anywhere inside the county, and a permanent 10 percent discount for seniors and veterans. If you’ve got a written estimate from another company already in hand, bring it in. We’ll give you a free second opinion on it, then beat it if the scope matches.

DIY or Call Us?

There are a few things you can check safely before you pick up the phone: make sure the breaker feeding the gate operator hasn’t tripped, confirm the keypad’s getting power if it has an indicator light, and look at the wiring inside the keypad housing for anything obviously chewed or disconnected. That’s where it stops. Access control wiring runs low voltage, so a brush against a live line will sting but it won’t throw you across the yard. The real hazard is the gate operator itself: the moment you open that control box, you’re standing next to a high-voltage supply and a capacitor bank that can hold a charge after the power is off. We’ve met more than one homeowner who got zapped swapping a receiver while the operator was still energized. Let us handle the board side of it. Call (817) 241-4067 and we’ll get you on the schedule. If I hand you my number, use it. That’s what it’s there for.

FAQs