Viking Gate Installation Nationwide | Gatewood Fence & Gate

Viking Gate Installation in North Richland Hills: What to Know First

We install Viking gate openers and full Viking gate systems in North Richland Hills, and we do it as an independent Viking service provider - meaning we answer to you, not to a manufacturer’s territory map. Most Viking installations take a half day to a full day once parts are in hand, and the price is quoted and agreed before any work starts. If you own a Viking opener that’s dead, a Viking gate that’s sagging, or you’re building new and want a Viking swinging or sliding setup, call (817) 241-4067 and a live person picks up.

Call (817) 241-4067

This page is for the homeowner in North Richland Hills who already has Viking equipment or has decided that’s the brand they want. We’ll tell you what fails on Viking systems, what it costs to install them here, and why we handle them differently than the company that just wants to sell you a whole new setup.

How Viking Products Fail - and How We Fix Them

Viking gets a lot right, but every brand has its habits. Here’s what we see on Viking installs around North Richland Hills:

• Viking G-5 and X-9 series control board corrosion. The boards are sealed well from the factory, but North Richland Hills gets real humidity swings in late spring, and we’ve pulled boards where condensation worked its way into the relay contacts. The opener will click but not move, or it’ll open halfway and stop like it lost its memory. We test the board’s output before condemning it - sometimes it’s a $40 limit switch saving you a $300 board.
• Viking L-3 linear actuator mounting brackets loosening. These actuators push and pull thousands of times a year, and the factory bracket bolts want to walk on steel posts. When they loosen, you get a gate that shudders at the start of travel and sounds like a toolbox falling down the stairs. We shim, re-drill if needed, and torque everything to spec - and we weld the bracket if the post is good enough to take it.
• Photo eye alignment on Viking sliding gates. Viking’s photo eyes are sensitive to post movement, and we see a lot of gates in North Richland Hills where the post shifted half an inch after a big rain and now the gate reverses every time. The homeowner thinks the motor’s going out. Most of the time it’s just realignment, plus a spacer block so the post can’t wander again.
• Dead batteries in Viking solar gate openers. Viking sells solar kits, and they work - but not forever. The sealed lead-acid batteries in the V-2 solar line typically cook themselves after three or four Texas summers. Your gate works fine all winter, then in July it opens twice and quits. We replace the battery with a proper deep-cycle equivalent and test the charge controller before calling it done, because if the controller’s bad, a new battery just dies slower.
• Viking gearbox oil leaks on swing arm models. The older Viking V-5 swing arms had a weep hole that occasionally weeps a little too much, and we’ll find a slick of oil under the arm and a gate that groans on every cycle. We drain, reseal, and refill with the right grade - or replace the arm if the gears are already chewed. A groaning Viking swing arm never fixes itself.

A gate sags in the hinge post, not in the middle - and that is where we start. On a Viking install in North Richland Hills that was never quite right, we check the post first. A lot of “Viking problems” are actually post problems wearing Viking parts out faster than they should.

Our Viking Gate Installation Process

Here’s how a Viking job goes at Gatewood Fence & Gate, start to finish:

1. 1
   You call, a person answers. Hal Gatewood or one of the crew picks up. We ask what the gate’s doing, or not doing, and we tell you if it sounds like a service call or a full install.
2. 2
   We show up and look at what’s actually there. Post depth, gate weight, panel condition, opener model, wiring, the whole picture. We don’t quote a Viking install over the phone without seeing the post and the hinges, because a gate sags in the hinge post, not in the middle.
3. 3
   You get a written price, and we agree on it before any work starts. No trip charge inside the county. If you have another written estimate, we’ll give you a free second opinion.
4. 4
   We install right - OEM Viking parts when it matters, quality aftermarket when it makes sense. We’ll tell you which is which and why. The price is agreed before the part goes on.
5. 5
   We test it hard. Open, close, reverse, photo eyes, force settings, the manual release. We run it ten times, and we watch it.
6. 6
   You get the 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back. No runaround, no fine print.

Hal’s been at this in North Richland Hills since 2001, and he welds on site - the gate stays in your driveway, not on a truck headed to somebody’s shop across the county.

What Viking Gate Installation Costs in North Richland Hills

Straight numbers. Here’s what we see in North Richland Hills for Viking work:

• Viking opener installed on an existing gate: $850 - $1,500, depending on model and post conditions.
• Full Viking slide gate with opener, installed: $3,800 - $6,200, depending on gate length, steel gauge, and whether the track base needs concrete work.
• Full Viking swing gate (single) with opener: $2,600 - $4,500. Double swing gates run higher - two posts, two hinges sets, two operators.
• Viking pedestrian gate with keypad and strike: $1,400 - $2,800.
• Control board or actuator replacement on existing Viking opener: $275 - $650, parts and labor.

What moves the price: post condition, gate weight, whether we’re pulling new power, and how far the gate sits from the house. We quote the price before we touch a single bolt. Call (817) 241-4067 for an exact number on your Viking install - the estimate is free, and we mean that.

Why North Richland Hills Homeowners Call Gatewood Fence & Gate for Viking Work

We’re locally owned and owner-operated, and Hal Gatewood’s name is on the shop and on every invoice. That’s not a marketing line - the shop is down the road, the address is published, and the license number is something anyone can look up. We’ve been fixing gates since 2001, and most of our regulars know Hal from the Smithfield Road corridor where he grew up and still lives.

Every Viking job carries the 90-Day Done Right Promise in writing. If it’s not right, we come back. No “up to,” no “in most cases.” And because we service nine brands - LiftMaster, Mighty Mule, Ghost Controls, DoorKing, and others - we’re not going to sell you a Viking part just because that’s all we know. We fix what needs fixing, and we tell you when your money’s better spent on a solid aftermarket part that’ll outlast the OEM. We’re also certified on the brands that compete with Viking, so when a Viking opener’s not worth saving, we can tell you what is - and back it the same way.

And we answer the phone. Around the clock, a live person picks up. Not a voicemail, not a recording. If I hand you my number, use it - that’s what it’s there for.

FAQs