Elite Gate Access Control Nationwide | Gatewood Fence & Gate

Elite Gate Access Control in North Richland Hills: What to Know First

We provide independent Elite gate access control repair and installation in North Richland Hills, with most keypad and entry system fixes done in a single visit. A typical Elite access control repair in this area runs $185 to $465, and we quote the full price before any work begins - not an estimate that changes when the invoice lands. If you’ve got an Elite keypad that stopped talking to the opener, or a phone entry system that rings but won’t release the gate, call (817) 241-4067 and a person answers.

Call (817) 241-4067

This page is for homeowners in North Richland Hills who already own an Elite gate opener or Elite access control system and need someone who actually understands how these units are wired, not someone reading a manual for the first time in your driveway.

How Elite Products Fail - and How We Fix Them

• Elite SL-3000 keypads losing programming after a power flicker. The SL-3000 series stores codes in memory that doesn’t always survive a brownout cleanly. We see this a lot in North Richland Hills during thunderstorm season. The fix is usually a full reprogram plus a small inline surge protector on the low-voltage line, which the original install rarely has.
• Elite PR-1 photo eyes tripping the gate for no reason. The PR-1 beam pair is sensitive to sunlight at certain angles, which is why gates along Davis Boulevard and Smithfield Road start refusing to close in late afternoon. We re-aim the eyes, shade the receiver, and where the wiring was spliced with wire nuts by a previous installer, we replace it with weatherproof connectors.
• Elite telephone entry systems that ring the house but won’t buzz the gate open. On the Elite EKT series, the relay output can fail while the phone side keeps working - so the owner hears the call, presses 9, and nothing moves. We test the relay with a meter, and when it’s dead we replace the relay board rather than selling you a whole new entry system.
• Elite REM-100 remote receivers going deaf after a year or two. The antenna wire on these is short and often tucked inside a metal enclosure, which kills range. Re-routing the antenna outside the box restores most of what owners think they lost. If you’re standing at the gate pressing the remote and it only works from 10 feet away, that’s usually the cause.
• Elite openers that work from the keypad but not from the remote, or vice versa. That’s a wiring or board-input problem, not the opener motor. We trace each input separately. Elite boards have independent terminals for the keypad, the receiver, and the loop detector, and one loose wire makes it look like a dead opener.

Our Elite Gate Access Control Process

1. 1
   You call, a person answers. Tell us your gate is doing. We ask a few questions only so the person who shows up brings the right parts.
2. 2
   We verify the problem with tools, not guesses. We ring out the wiring, test the relay outputs, check the transformer voltage, and watch the gate run a full cycle. On an Elite system we don’t blame the motor until the inputs are ruled out.
3. 3
   We tell you exactly what’s wrong and what it costs. You get a firm price for the repair before any work starts. If it’s a $6 terminal block and not a $300 keypad, we tell you that.
4. 4
   We make the repair with parts that match the job. For the boards and keypads that talk to the opener, we use Elite parts or a proven equivalent that won’t void an active warranty. For generic supports, enclosures, and wiring, we use what lasts in North Richland Hills weather.
5. 5
   We test it three ways. Keypad opens the gate. Remote opens the gate. Phone entry opens the gate. And then we cycle the gate ten times while we watch the hinges and the catch, because access control doesn’t matter if the gate itself is binding.
6. 6
   We leave you the paperwork. Your price is on it, and so is the 90-Day Done Right Promise in writing. If it acts up again, one call brings us back.

What Elite Gate Access Control Costs in North Richland Hills

Here’s what most North Richland Hills homeowners pay for common Elite access control work:

• Keypad diagnosis and reprogram: $85 to $160
• New Elite keypad replacement, installed: $240 to $420
• Relay board replacement on an Elite EKT phone entry unit: $185 to $310
• Photo eye re-aim, re-shade, or one new PR-1 sensor: $120 to $225
• Full access control retrofit (new keypad, receiver, enclosure, wiring cleanup): $520 to $980

What moves the price is what we find when we open the box - bad splicing from the last installer, water that got into the enclosure, or a gate that’s binding and will eat whatever electronics you throw at it. We quote everything upfront, before we touch a wire. Estimates are free, and the price you agree to is the price you pay.

Why North Richland Hills Homeowners Call Gatewood Fence & Gate for Elite Work

We’ve fixed gates in North Richland Hills since 2001, and most of our regulars know Hal Gatewood from the Smithfield Road corridor - he grew up here and still lives here. When an Elite system acts up, the person who shows up to fix it has welded and wired enough of these openers to know what fails and why. And when a previous installer left a mess - misaligned hinges, wire nuts where weatherproof connectors belong, or an opener wired with what Hal charitably calls “creative thinking” - we set it right.

Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so when a North Richland Hills property has a mixed setup - an Elite opener here, a Ghost Controls swing arm there - one call covers all of it. Call (817) 241-4067 and a person answers, day or night. Not a voicemail, not a call center.

FAQs