Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterWeld & Rust Repair in North Richland Hills, TX
When your iron gate starts to sag or the steel frame shows signs of flaking, you do not need a new gate. You need a welder who knows how to fix the structure so it lasts another decade. At Gatewood Fence & Gate, we specialize in our Gate Repair services, including on-site weld and rust repair for homeowners across North Richland Hills. We do not haul your gate off to a shop, and we do not try to sell you a replacement when a simple repair will solve the issue. If your gate is pulling away from the post or the metal has rusted through at the base, call us at (817) 241-4067. We offer honest assessments and upfront pricing because we believe in fixing what is broken, not pushing you toward a product you do not need.
Rust is a constant battle in North Texas. Our local humidity, combined with the extreme heat cycles we see here, creates the perfect environment for oxidation. If you ignore a small patch of rust, it eventually eats through the steel, compromising the structural integrity of your entire entry system. My name is Hal Gatewood, and I have been fixing gates since 2001. I have seen the damage that happens when people let rust go too long, and I know that the best way to handle it is to address the metal fatigue early. If you are looking for professional Gate Repair in North Richland Hills, we are here to help.
When You Need Weld & Rust Repair
Not every gate problem is a mechanical motor issue. Often, the trouble starts with misalignment or the steel itself, which is why Gate Realignment may be needed. You should call for a professional evaluation if you notice any of the following signs of failure:
- Structural Sagging: If your gate is dragging on the concrete or no longer lines up with the latch, it is likely that the hinge post has shifted or a weld has snapped. This is a common issue in North Richland Hills where our clay soil expands and contracts, putting stress on the gate frame.
- Visible Flaking or Pitting: If you can scrape the surface of the metal and find loose, flaky rust, the corrosion has likely penetrated the primer. Paint will not fix this; you need to grind it down to bare metal to stop the spread.
- Popped or Cracked Welds: Over time, the vibration of the gate opening and closing causes welds to fatigue. If you see a gap between the picket and the rail, or where the frame meets the hinge, that is a structural failure that needs immediate welding.
- Hinge Failures: When the hinge itself is rusted into the post, the gate becomes difficult to operate and puts extreme strain on your gate motor. We often see this when the original installation lacked proper weather sealing.
- Hollow Section Corrosion: If your gate frame is made of hollow steel tubing, water can get trapped inside, causing it to rust from the inside out. If you see bubbling paint on the frame, the metal is compromised from within.
If you see these issues, it is time to act. A gate that is not moving correctly is more than just an inconvenience. It is a security risk. A heavy gate that is failing can also be a safety hazard for your family and pets. As a locally owned and owner-operated business, we take pride in doing the job right the first time. We are the home for reliable, straightforward gate service in this area.
Our Weld & Rust Repair Process
Welding is a craft that requires patience and the right equipment. You cannot simply patch over rust and expect it to hold. When we arrive at your home in North Richland Hills, we follow a strict process to ensure the repair is permanent. Please note that welding involves high-voltage electricity, intense heat, and UV light; for your safety, this is not a task you should attempt without professional training and proper protective gear.
- Inspection and Assessment: We start by examining the entire frame, not just the spot where you see the rust. Often, if one weld has failed, others are close behind. We check for structural integrity to ensure the gate is safe to repair.
- Surface Preparation: This is the most important step. We grind away all the rust, old paint, and corrosion down to the bare, bright metal. If we do not get to the clean steel, the rust will simply return under the new paint.
- Weld Reinforcement: We use high-quality welding equipment to fuse the metal back together. If the original metal is too thin from rust, we may need to cut out the damaged section and weld in a new piece of steel to restore the strength of the frame.
- Finishing and Sealing: Once the weld is strong, we grind the bead smooth so it looks clean. We then apply a high-quality, corrosion-resistant primer, followed by a finish coat that matches your gate. This seals the metal against the North Texas weather.
- Operational Check: After the weld is cool and the finish is dry, we test the gate to ensure it swings or slides perfectly. We make sure the gate is balanced and that there is no unnecessary strain on the motor or the hinges.
We stand behind every job with our 90-Day Done Right Promise. If the weld fails or the repair does not hold, you call us, and we come back to fix it. That is the kind of accountability you get when you hire a local owner-operator like Hal Gatewood.
Weld & Rust Repair Pricing in North Richland Hills
We believe in upfront pricing. You will never be surprised by a bill when we are finished. While every gate is different, we can provide some general guidelines on what you might expect to pay for professional on-site weld and rust repair. The final cost depends on the severity of the rust, the amount of steel that needs to be replaced, and the complexity of the gate design.
| Service Type | Estimated Range |
|---|---|
| Minor Weld Spot Repair | $150 - $250 |
| Hinge Re-welding & Reinforcement | $200 - $350 |
| Extensive Rust Removal & Patching | $300 - $600 |
| Frame Repair (Structural) | $400+ |
We offer a standing $40 discount on any repair over $200. We also provide a permanent 10% discount for seniors and veterans. If you have a written estimate from another company, we are happy to offer a free second opinion. We do not charge a trip fee for jobs within the county. Call us at (817) 241-4067 to discuss your gate and get an accurate quote. We answer the phone 24 hours a day, 7 days a week, so you are never left waiting for a callback.
FAQs - Weld & Rust Repair
How do I know if my gate can be repaired or if it needs to be replaced?
Most gates can be repaired with Electric Gate Repair if the main frame is still structurally sound. If the rust has eaten through the majority of the bottom rail or the posts are leaning so far that the gate cannot close, replacement might be the only option. However, we always try to repair first. We will tell you honestly if a repair is just a temporary fix or if it will provide a long-term solution.
Can you match the paint on my existing gate?
We do our best to match the color and finish of your existing gate. While we cannot always guarantee a perfect match due to sun fading on the original paint, we use high-quality, weather-resistant coatings that protect the metal and blend in with the rest of the structure. If your gate has a custom powder-coat finish, we will use a heavy-duty industrial enamel that provides similar protection.
Is it safe to weld a gate while it is still hanging?
In many cases, yes, we can perform repairs while the gate is hanging. This saves you the cost and hassle of removing the gate and hauling it to a shop. However, if the damage is severe, we may need to remove the gate to ensure a safe and strong weld. We always assess the gate on-site to determine the safest and most effective method. We work with major brands like LiftMaster, FAAC, and Ghost Controls, so we are familiar with how different gate systems are built and how to perform Automatic Gate Repair without causing further damage.
How long does a weld repair usually take?
Most minor weld repairs can be completed in a single visit, often within a few hours. More complex repairs involving significant steel replacement or extensive rust removal may take longer. When you call us, we will give you a clear time estimate based on the description of the damage. We respect your time and schedule, and we do not like to leave a job half-finished.
If you are dealing with a rusted or broken gate, do not let it turn into a bigger problem. Small issues with steel and welds tend to grow quickly in our climate. My team and I are ready to get your gate back in working order with the kind of service that makes you want to recommend us to your neighbors. We have been serving this community since 2001, and we plan on being here for many years to come.
Call (817) 241-4067 today for a free estimate or to ask any questions about your specific gate issues. We are ready to help.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving North Richland Hills.