FAAC Gate Motor & Opener Nationwide | Gatewood Fence & Gate

FAAC Gate Motor & Opener in North Richland Hills: What to Know First

FAAC gate motor and opener repair in North Richland Hills typically runs $190 to $480 depending on whether we’re replacing a capacitor, swapping a control board, or rebuilding a gearbox that’s been grinding itself down for a year. Most jobs are done the same day we look at them, unless we’re waiting on a specific FAAC board to come in. This page is for homeowners in North Richland Hills whose FAAC opener quit, runs but won’t move the gate, or starts and stops on its own. Call (817) 241-4067 and a live person answers, any hour.

Call (817) 241-4067

How FAAC Products Fail - and How We Fix Them

FAAC builds a solid operator. But every brand has its habits, and after 24 years of opening FAAC boxes in North Richland Hills driveways, we know where they give up first.

• FAAC 422/400-series capacitor failure: The 400-series operators, common on residential swing gates throughout North Richland Hills, run on a start capacitor that swells and dies in Texas heat. The symptom: the motor hums but the gate doesn’t move. Some companies quote a full motor replacement. We test the capacitor first, and nine times out of ten that’s the fix, under $200 installed.
• FAAC 750/760 hydraulic pump seal leaks: The 750 and 760 models are workhorses, but their hydraulic seals dry out and crack after 8 to 12 years, especially with the temperature swings we get between summer and winter in North Richland Hills. You’ll see oil stains under the operator box. The fix is a seal kit and fresh hydraulic fluid, not a new unit.
• Limit switch drift on FAAC slide operators: FAAC slide motors, like the 844, use mechanical limit switches that can drift after years of vibration. The gate stops short, or overtravels and slams the end stop. We re-set the limits, check the torque, and confirm the gate coasts to a soft stop. Takes about 45 minutes.
• Control board solder joints on older FAAC 413/415 boards: We see cold solder joints on boards from the mid-2010s, especially where the transformer meets the PCB. The gate works intermittently, which drives owners crazy. We reflow the joints when safe, or install a new board when the pad is burned through.
• Battery backup neglect on FAAC E024U kits: North Richland Hills gets its share of storms, and FAAC battery backup kits fail not from use but from sitting. The battery sulfates, the charger floats wrong, and when the power drops, the gate doesn’t open. We test the battery under load, not just with a voltmeter, which catches failures a quick check misses.

Our FAAC Gate Motor & Opener Process

1. 1
   You call. A live person answers (817) 241-4067. No voicemail tree, no call center. Hal or one of his crew listens to what the gate’s doing, or not doing.
2. 2
   We arrive on time. Inside the county, no trip charge. In North Richland Hills, we’re local, so we know the streets, from Smithfield Road to Davis Boulevard.
3. 3
   We diagnose in front of you. We open the FAAC box, test the capacitor, board, and limits, and tell you exactly what failed and why. You see what we see.
4. 4
   We price it before work starts. No surprise invoice at the end. OEM FAAC part if the warranty or board demands it, quality aftermarket when it’s honestly the better value, and we spell out which is which.
5. 5
   We fix it in your driveway. We weld on site if bracketry or a hinge post is involved. The gate stays where it is, and the repair is done before we leave.
6. 6
   We test it hard. Ten full cycles minimum, checking slow-down zones, safety edges, and stop points. Then Hal writes the 90-Day Done Right Promise on the invoice, in plain ink.

What FAAC Gate Motor & Opener Costs in North Richland Hills

Here’s what we see, honestly priced, on FAAC jobs in North Richland Hills:

• Capacitor replacement: $160 to $240 installed, depending on model and access.
• Control board replacement (aftermarket): $280 to $450. OEM FAAC boards run higher, and we tell you the difference before ordering.
• Limit switch repair or replacement: $120 to $200, including re-setting travel and force.
• Hydraulic seal and fluid service (750/760): $240 to $380.
• Full FAAC operator swap (labor and operator): $1,300 to $2,200, depending on gate weight and whether we’re reusing your existing mounting plate.

What moves the price: gate size and weight, how many cycles a day it runs, whether the problem is electrical, hydraulic, or mechanical, and whether someone before us wired things creatively. Estimates are free. The number we quote is the number you pay.

Why North Richland Hills Homeowners Call Gatewood Fence & Gate for FAAC Work

FAAC operators are only as good as the person who installed and last serviced them. We’ve been fixing gates in North Richland Hills since 2001, and Hal Gatewood’s name is on the shop, on the invoice, and on the work. We’ve seen FAAC units hacked up by people who didn’t know a limit switch from a capacitor, and we’ve rebuilt them right. If the FAAC unit isn’t worth saving, we’ll tell you straight, and we can quote a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing replacement that fits the same gate. One crew, one name, 90 days in writing. If I hand you my number, use it, that’s what it’s there for.

FAQs