Ghost Controls Gate Installation Nationwide | Gatewood Fence & Gate

Ghost Controls Gate Installation in North Richland Hills: What to Know First

We install, repair, and retrofit Ghost Controls gate openers throughout North Richland Hills, and most jobs are done within two to five business days of the first call. A standard Ghost Controls installation on an existing gate runs $450 to $900, depending on the opener model and whether the gate needs hinge or post work before the opener goes on. You’ll get a written price before we touch anything, and the price we quote is the price you pay. If you own a Ghost Controls opener and need it mounted, wired, or replaced on a driveway gate, pedestrian gate, or double gate, call (817) 241-4067 and we’ll talk through what you’ve got.

Call (817) 241-4067

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls makes a solid opener for the money, but we see the same handful of problems repeat themselves across North Richland Hills driveways. Here’s what actually goes wrong, series by series:

• AXDP and AXD series: limit switch drift after power flickers. The magnetic limit switches on the Ghost Controls AXDP and AXD series lose their position when a storm knocks power out mid-cycle. The opener still runs, but it over-travels and slams the gate against the post. The fix is a full limit relearn and a physical stop check, not a parts swap. We see this most often on the west side of North Richland Hills near the open lots, where lightning takes the grid down a few times each spring.
• HYDRAULIC series: control board corrosion from North Texas dew cycles. The Ghost Controls Hydraulic series boards sit in a housing that breathes, and Tarrant County humidity finds its way in. We pull boards with green fuzz on the solder joints every month. If the corrosion hasn’t eaten the traces, we clean and seal the board and add a desiccant pack; if it has, we replace the board and seal the new housing properly. Ghost Controls won’t tell you the housing needs extra sealing here, but it does.
• TSS1 and TDS1: solar panel wiring too short for proper southern exposure. The solar kits Ghost Controls ships with the TSS1 and TDS1 are wired for a fence-post mount about eight feet from the gate. That’s fine on paper, but on the north side of a North Richland Hills house with a two-story garage shading the post, the panel never gets enough sun and the battery dies within weeks. We remount the panel on the sun-facing side and run proper gauge wire, which means the opener actually holds a charge.
• R3BEL and other touchpad models: touchpad membrane fails from UV + bug residue. The touchpads on Ghost Controls R3BEL openers crack and fog under the Texas sun, and once the membrane splits, dirt and crickets get inside and the keypad starts ghost-pressing. We replace the touchpad with a newer sealed unit and add a shade hood, which adds a few years to the part.
• ALL series: factory arm geometry is too short for a wide driveway gate. Ghost Controls ships arms sized for gates up to 16 feet, but a 14-foot gate with a sagging hinge post effectively swings like an 18-foot gate. The opener arm then over-extends and bends at the clevis pin. Before we mount any Ghost Controls arm, we measure the actual swing arc and check the posts, not just the gate width from the box.

Our Ghost Controls Gate Installation Process

Here’s what a Ghost Controls installation looks like when we do it:

1. 1
   Call and look. You call (817) 241-4067, a person answers, and we set a time to come see the gate. We don’t quote over the phone on a Ghost Controls install because we need to see the posts, the hinge hardware, and the power situation first.
2. 2
   Measure everything. Gate weight, swing arc, post gauge, clearance on both sides, and whether the opener will be AC, DC, or solar. If the posts are loose or the hinges are worn, we tell you then and we fix those before the opener goes on, because an opener mounted on a bad post eats itself in months.
3. 3
   Parts decision. If your Ghost Controls opener can be saved, we use OEM parts when they’re available and the right aftermarket parts when they’re not, and we tell you which is which. For a new install, we typically use the Ghost Controls kit you’ve purchased or one we order in, and we never substitute a different brand without asking first.
4. 4
   The mount. We weld brackets and reinforcing plates where they belong, not sheet metal screws through a 16-gauge post. On-site welding means the gate never leaves your driveway.
5. 5
   Wire and program. Limits, force, auto-close timing, obstruction sensitivity, and all remotes and keypads are set and tested at least ten full cycles with weight on the gate.
6. 6
   The promise. You get the 90-Day Done Right Promise in writing. If something isn’t right, we come back and make it right. No phone tag, no gatekeepers.

What Ghost Controls Gate Installation Costs in North Richland Hills

Straight numbers, the way we’d give them over the phone if we could see the gate from the truck:

• Basic single swing gate, opener already in hand: $450-$650. Includes mount, wiring, programming, and testing.
• Single swing gate with hinge or post repair first: $650-$1,100. The post work is usually the bigger half of that.
• Double gate with one Ghost Controls arm per leaf: $800-$1,400. Two arms, two mounts, twice the limit programming, and typically a center stop to install.
• Sliding gate with Ghost Controls opener: $700-$1,200, depending on the track and roller condition.
• Full rip-out of an old opener and Ghost Controls retrofit: Add $150-$300 for removal and cleanup of the old unit and its wiring.

What moves the price is the gate’s condition and the power run. A long trench from the house to a gate 60 feet away costs more than a gate with an outlet already at the post. We quote it before we start, in writing, and that’s the number. Call (817) 241-4067 for a free estimate and we’ll give you a number you can plan around.

Why North Richland Hills Homeowners Call Gatewood Fence & Gate for Ghost Controls Work

The name on the shop is Hal Gatewood’s, and the shop is down the road. Hal has been fixing gates in North Richland Hills since 2001, and most of his regulars know him from the Smithfield Road corridor where he grew up and still lives. When you call, you’re not getting routed to a person in another state who’s never seen a Ghost Controls opener. You’re getting Hal or one of his guys, a person who shows up in a truck with welding gear and a phone number you can call back. Every Ghost Controls job carries the 90-Day Done Right Promise in writing, and we don’t make you haggle for a fair price. We also service LiftMaster, Mighty Mule, and DoorKing openers, so if your Ghost Controls unit turns out to be beyond saving, we can show you what else will work on your gate and give you a straight recommendation. A live person answers the phone around the clock, and Hal will be the first to tell you: if he hands you his number, use it, that’s what it’s there for.

FAQs