Ghost Controls Gate Parts & Welding Nationwide | Gatewood Fence & Gate

Ghost Controls Gate Parts & Welding in North Richland Hills: What to Know First

We repair Ghost Controls gate openers and weld the steel work around them in North Richland Hills, and most jobs are done within one to three days of your call. You’ll get a firm price before we touch anything, and we never charge a trip fee inside Tarrant County. If you’re a Ghost Controls owner whose gate is sagging, grinding, or swinging loose, call (817) 241-4067 and we’ll tell you what’s wrong and what it’ll cost.

Call (817) 241-4067

This page is for the homeowner who already owns a Ghost Controls system and needs someone who actually knows the product, not a parts-swapper guessing at it. We’re an independent Ghost Controls service provider. We don’t sell their openers off a shelf, and we’re not a warranty depot. What we do is fix them properly, weld the metal so it stays fixed, and stand behind the work for 90 days in writing. Hal Gatewood has been doing this in North Richland Hills since 2001, and the shop’s phone is answered by a live person whenever you call.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls builds a solid opener, but every brand has its patterns. Here’s what we see on Ghost Controls gates in North Richland Hills:

• AXDP-series hinge bracket stress. The AXDP line’s opener arm mounts to a bracket that takes a beating on heavy gates. When the gate tube wall is too thin (common on 16-gauge farm gates), the bracket tears loose and the gate hangs dead. We remove the torn section, weld in a reinforcement plate, and remount the bracket so it can’t twist off again.
• Gate sag eating the limit stops. A Ghost Controls opener that was dialed in two years ago starts hitting its stops late because the gate itself has dropped at the hinge post. The opener didn’t change, the steel did. We weld a new hinge post sleeve or re-hang the gate so the opener’s travel matches the gate’s actual swing again. In North Richland Hills, the clay soil shifts with every wet-dry cycle and hinge posts creep, so this one’s common.
• Frayed actuator cable on the GTR-series arms. Ghost Controls GTR and GTX-series arms use an internal cable that can wear against the guide channel after years of exposure to clay dust and Texas sun. The symptom is a gate that moves in jerks but won’t finish a full cycle. We open the arm, inspect the cable path, and replace the actuator parts before they snap mid-open leaving the gate locked out.
• Bad limit magnets after a board replacement. When a Ghost Controls board gets replaced and the installer doesn’t reposition the limit magnets to match, the gate over-travels and slams the post. We see this often after DIY board swaps. We reset the magnet positions, weld a stop if the post has been beaten, and re-teach the board.
• Latch and lock misalignment after welding repairs. A gate that got welded or modified by a general welder without the Ghost Controls latch geometry in mind won’t close and lock cleanly. The opener’s force settings can’t compensate for a latch that’s off by a quarter inch. We weld and shim the latch post so the Ghost Controls lock engages without fight, and the opener isn’t pushing against its own limits.

Our Ghost Controls Gate Parts & Welding Process

Here’s exactly how a Ghost Controls gate parts and welding job goes when you call Gatewood Fence & Gate:

1. 1
   You call, a person answers. No voicemail, no press-1-for-gates. You describe what the gate’s doing, and we ask the kind of questions that tell us whether we’re dealing with a steel problem, an actuator problem, or a board problem.
2. 2
   We come out and diagnose on site. For most Ghost Controls issues, we come by, put hands on the gate, and identify what actually failed. We don’t guess over the phone.
3. 3
   Parts decision: OEM or better-quality aftermarket. If your Ghost Controls opener is under warranty, we use Ghost Controls factory parts so you don’t void that warranty. If it’s out of warranty, we quote you the factory option and the equivalent aftermarket option where one exists, and tell you honestly which one we’d put on our own gate.
4. 4
   The repair gets done in your driveway. We weld on site, so the gate stays put. We don’t haul it to a shop, we don’t leave you without an opening overnight.
5. 5
   We test the full cycle. After the repair, we run the opener through open and close with resistance checks, make sure the limit stops line up, and confirm the latch and lock engage cleanly.
6. 6
   We hand you the 90-Day Done Right Promise in writing. If anything we touched fails in 90 days, call us, and we come back and fix it. That’s the whole promise.

What Ghost Controls Gate Parts & Welding Costs in North Richland Hills

Here’s straight talk on what we typically quote for Ghost Controls work in North Richland Hills:

• Hinge replacement (welded, not bolted): $175-$350 per hinge, depending on gate weight and post access.
• Opener arm actuator cable and guide replacement: $140-$280 in parts and labor, assuming the board itself is fine.
• Bracket re-weld with reinforcement plate: $95-$220, including grinding, prep, and cleanup.
• Latch and lock realignment: $80-$180, often paired with welding if the latch post has shifted.
• Full gate re-hang with new welded hinge posts: $600-$1,400, depending on gate size, soil condition, and whether the old posts need extracting.

What moves the price is gate weight, post gauge, and whether we’re correcting someone else’s previous repair. What doesn’t move it is surprise fees. You get the quote before any work starts, and if you have a written estimate from another company, bring it by and we’ll give you a free second opinion. Call (817) 241-4067 for an exact number on your gate.

Why North Richland Hills Homeowners Call Gatewood Fence & Gate for Ghost Controls Work

We’ve been fixing gates in North Richland Hills since 2001, and most of our Ghost Controls work comes from homeowners who already tried another company and got a gate that still doesn’t close right. Hal Gatewood grew up off Smithfield Road and still lives here, so when we promise something, he’s accountable to his own neighbors, not a district manager in another state. Every Ghost Controls job we do carries the 90-Day Done Right Promise in writing, and a live person answers the phone 24/7. We also service LiftMaster, Mighty Mule, and DoorKing systems, so if you have more than one gate on the property with different brands, one call covers all of them. The crew is background-checked and uniformed, and the one who shows up is the one who’ll remember your gate next time.

FAQs