Ghost Controls Hinge & Roller Replacement Nationwide | Gatewood Fence & Gate

Ghost Controls Hinge & Roller Replacement: The North Richland Hills Owner’s Guide

Ghost Controls hinge and roller replacement in North Richland Hills typically runs $185 to $420 installed, depending on which hinge set your gate uses and whether the rollers need new brackets welded in. We stock Ghost Controls-compatible hinges and rollers on the truck, and in most cases we can have your gate swinging right the same day we show up. You usually discover these parts have failed when the gate starts dragging across the driveway, the latch no longer lines up, or the gate develops a lean that keeps getting worse week to week. What starts as a little scrape on the concrete turns into a bent pickup post and a motor that’s working twice as hard as it should.

Call (817) 241-4067

Hal Gatewood has been fixing Ghost Controls gates in North Richland Hills since 2001, and he’ll tell you straight: hinge and roller failures are the most common repair that other companies misdiagnose as “you need a whole new gate.” Most of the time you don’t.

Which Ghost Controls Models This Applies To

Ghost Controls builds modular gate kits sized for residential driveways, and the hinge and roller hardware follows a few patterns rather than a different part for every box. If you’ve got a Ghost Controls single or dual swing gate kit, you’re almost certainly dealing with barrel-style hinges that bolt through the gate frame and into the post. The TSS1, TDS1, and the older residential kits released before the current heavy-duty series all use variations of the same hinge barrel, though the pin diameter changed on some 2020 and newer kits when Ghost moved to a thicker pin on their heavy-duty option.

Here’s what matters for matching the part: measure the hinge barrel length and the pin diameter with a tape measure before you call anyone. Ghost Controls hinges typically have a barrel length between 3 and 4 inches, with pin diameters of 3/4 inch on the standard series and 7/8 inch on the heavy-duty versions. If you’ve got the original manual, the parts diagram lists a hinge part number that starts with GH, and that number makes matching exact. If you don’t have the manual, we match by measurement at the gate, and we’ve got OEM Ghost Controls parts plus quality aftermarket equivalents that meet the same load rating. For rollers, Ghost gates run either a rolling track wheel at the free end or a ground roller assembly, and the mounting bracket is the thing everyone gets wrong. We check the bracket before we swap the wheel, because a fresh roller on a bent bracket wears out in six months.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• The gate leans toward the latch or away from it. A gate sags in the hinge post, not in the middle, and that lean means a hinge pin has worn or a mounting bolt has loosened. The fix is a new hinge set and re-shimming the post side before it pulls the post out of plumb.
• The gate scrapes or drags at the end opposite the hinges. This is usually the roller wheel binding or losing its bearing, and it pushes all that weight onto the hinge side. Left alone, it ruins the hinge pins trying to save the roller’s job.
• The latch bolt no longer drops into the catch without lifting the gate. Misaligned latch hardware is rarely a latch problem; it’s the hinge or roller telling you the gate has settled. Repositioning the latch without fixing the height is how you get a gate that only latches when you hold your mouth right.
• The gate makes a screech or groan when it moves. Hinge pins dry out and gall, especially after a North Texas summer bakes the grease out of the barrel. By the time it screams, the pin is usually too scored to save.
• The opener struggles or strains at the start of travel. Ghost Controls openers are fine little motors, but they weren’t built to drag a gate with collapsed rollers. If yours sounds like it’s working harder than it used to, the hinge and roller wear is probably the cause.

Replacement Cost & What’s Included

Here’s the pricing picture for North Richland Hills, and this is what you should expect to see on a written estimate:

• Hinge replacement only (per pair): $185-$275 installed, including hardware, shimming, and post inspection
• Roller assembly replacement (wheel plus bracket): $140-$220 installed, including welding the new bracket if the old one snapped or bent
• Full hinge and roller replacement on one gate leaf: $300-$420 installed, including realigning the gate and adjusting the latch
• On-site welding (if the bracket or mounting tab failed): $60-$110, done in your driveway, not hauled off to some shop

The range comes down to what we find when we get the gate on a jack: if the post is still solid and the metal around the hinge mount is sound, you’re at the low end. If the previous installer used hardware that was too light for the post gauge, or the gate has been scraping long enough to waller out the mounting holes, that’s extra welding time and a heavier hinge. Every job carries our 90-Day Done Right Promise in writing, and the price is quoted and agreed before any work starts. No trip charge inside the county, and there’s $40 off any repair over $200.

DIY or Call Us?

Replacing Ghost Controls hinges and rollers looks simple, and sometimes it is. If your gate is a light single-leaf unit and you’re handy with a socket set, a patient DIYer can swap hinge pairs on a weekend afternoon. What you should not do is attempt to weld a torn roller bracket or shim a leaning post without knowing what’s plumb looks like through a gate’s swing arc. The hinge and roller carry the full weight of the gate, and a gate that drops because a mounting point let go can hurt someone. That’s the kind of failure you don’t get a second try on.

What we do is put eyes on the whole assembly before we turn a wrench: post condition, hinge alignment, roller bracket integrity, opener strain. Then we fix what’s actually wrong, not just what’s rattling loudest. If you’re in North Richland Hills and want a straight answer, call (817) 241-4067. A live person answers, and if Hal picks up, it’s him. If I hand you my number, use it - that’s what it’s there for.

Frequently Asked Questions About Ghost Controls Hinge & Roller Replacement in North Richland Hills