Ghost Controls Keypad & Intercom Repair Nationwide | Gatewood Fence & Gate

Ghost Controls Keypad & Intercom Repair: The North Richland Hills Owner’s Guide

Ghost Controls keypad and intercom repair in North Richland Hills typically runs $185-$410 installed, and we carry the common boards, wiring kits, and aftermarket keypads on the truck most weeks. If your opener responds fine from the remote but ignores the keypad, or the intercom buzzes but nobody hears anybody, you’ve usually got a wiring failure at the post, a corroded board, or a keypad that’s been sunbaked past saving. We’ll verify which one it is before we sell you anything.

Call (817) 241-4067

Most folks around here discover the problem the hard way: a delivery driver can’t get ahold of anyone, the kids’ code stops working, or a rainstorm turns the keypad into a brick. The good news is this is almost never a full opener replacement. Ghost Controls systems are modular enough that the keypad and intercom live on their own circuit, so when they die you fix that part, not the whole gate.

Key takeaways:

• Installed repair or replacement of a Ghost Controls keypad or intercom typically costs $185-$410 in North Richland Hills.
• The failure is usually in the low-voltage wiring or the keypad’s weather seal, not the opener motor itself.
• We’re an independent service provider, not affiliated with Ghost Controls, but we service their hardware weekly and keep compatible parts in stock.
• You’ll get a written price before any work starts, and the whole job carries the 90-Day Done Right Promise.

Which Ghost Controls Models This Applies To

Ghost Controls makes three main system families: the AXP, the GLD, and the newer hybrid solar packages. The keypads and intercoms don’t cross over cleanly between generations, which is where a lot of online ordering goes sideways. An AXP keypad wired directly to the control board won’t play nice with a GLD system that expects the wireless receiver module, and the solar units want a lower-voltage trigger than the old plug-in boards put out.

So before we order or pull anything off the truck, we look at two things: the label on the back of the keypad or intercom module, and the wiring terminal layout inside the control box. Ghost Controls stamps a part number and voltage range on the housing, and matching that number to the board’s terminal block takes about three minutes for a person who’s done it a few hundred times. We also see a fair number of homeowners who bought a universal aftermarket keypad online and wonder why it won’t fire the opener. The answer is usually that the Ghost Controls board wants a momentary dry-contact signal, and the universal pad is sending a latched output. That’s a ten-dollar relay fix, not a keypad problem, but you’d never know it from the error message you don’t get.

Signs Your Ghost Controls Keypad or Intercom Is Failing

• The keypad accepts a code but nothing moves. This usually means the keypad itself is fine and the output signal isn’t reaching the control board. Nine times out of ten it’s a corroded wire nut or a break at the post base where the conduit flexes.
• The intercom rings the house but audio is dead or full of static. The intercom draws a tiny bit of constant power from the board. A failing capacitor or a spider colony inside the housing can kill the audio path while the ring circuit still fires. We see that a lot after North Texas spring storms.
• The keypad only works when it’s cool outside. That’s a failing voltage regulator on the keypad board. Texas heat pushes it past its limit in the afternoon, and it recovers when the temp drops. It will get worse every summer until it stops altogether.
• One or two buttons stopped responding while the rest work. The membrane under the keys has cracked or delaminated. You can clean the contacts sometimes, but a cracked membrane means the pad has reached the end of its useful life.
• Ghost Controls intercom audio works one way only. One-way audio is almost always a wiring or board-level fault, not a speaker problem. We test the speaker with a meter before replacing anything, because swapping a working speaker for a new one and still having dead audio is exactly the kind of bill a homeowner should not have to pay.

Replacement Cost & What’s Included

In North Richland Hills, expect to pay roughly $185-$410 for a Ghost Controls keypad or intercom repair, installed and tested, depending on whether we’re repairing a wiring fault or replacing the unit outright. A basic wiring repair or relay fix at the control board runs on the lower end. A new aftermarket keypad with fresh weatherproof connectors lands in the middle. A full OEM Ghost Controls intercom module replacement, with the handsets and board, moves toward the top end.

The price we quote is the price you pay. Parts and labor are broken out, it’s all on the written estimate, and we don’t start until you’ve looked at the number and said yes. Every job carries the 90-Day Done Right Promise in writing. If the keypad misbehaves or the intercom audio drops within 90 days of the repair, one call brings us back. No runaround, no charge. That covers the part and the workmanship, and Hal’s name is on the invoice to back it.

And keep in mind: if you’re in Tarrant County, there’s no trip charge. Seniors and veterans get 10% off permanently. If the repair tops $200, you get $40 off – so if the intercom takes the higher-end fix, that’s already handled before we hand you the invoice.

DIY or Call Us?

Ghost Controls keypads and intercoms run on low-voltage DC from the control board, usually 12 or 24 volts depending on the series, so this repair is not in the same danger class as a tensioned gate spring or an opener motor wired directly to line voltage. You can safely check a few things yourself: make sure the keypad isn’t just full of dirt or water, verify the wiring connections at the keypad are snug, and confirm the opener still works from the remote. If the remote fires fine, that tells you the board and motor are good, and you’ve narrowed the problem to the keypad or intercom circuit.

Where DIY goes wrong is usually the wiring diagnosis. We’ve been called out after a well-meaning homeowner replaced a keypad that was never bad, because the original failure was a broken wire under the driveway or a relay that had given up inside the control box. We also see people installing a keypad without sealing the conduit entrance, and the next rainstorm turns the new part into the same old problem. If you’re not certain, call (817) 241-4067 and we’ll put eyes on it. The diagnosis is honest, and the estimate is free.

FAQs