Linear Gate Motor & Opener Nationwide | Gatewood Fence & Gate

Linear Gate Motor & Opener in North Richland Hills: What to Know First

We repair and install Linear gate motors and openers across North Richland Hills, and most jobs are done in a single visit. A typical Linear motor repair runs $180 to $400, and a full opener replacement usually lands between $650 and $1,200 depending on the model and what’s reusable. You’ll get that exact number before we touch a single bolt, and it won’t change at the door. If your Linear gate is acting up, call (817) 241-4067 and Hal or one of the crew will pick up.

Call (817) 241-4067

This page is for homeowners in North Richland Hills who own a Linear gate system and want straight answers about what’s wrong, what it costs, and whether it’s worth fixing. We’re an independent Linear service provider, not a factory shop, so the advice you get here is based on what we actually see in driveways around Smithfield, Holiday Heights, and the neighborhoods off Rufe Snow, not what a manual says should happen.

Key Takeaways

• Most Linear motor problems are fixed same-day for under $400.
• Linear’s capacitor issue (explained below) is the most common failure we see in North Richland Hills.
• Every job carries our 90-Day Done Right Promise in writing.
• Free estimate, no trip charge inside the county, and the price is locked before work starts.

How Linear Products Fail - and How We Fix Them

Linear makes decent equipment, but no gate opener survives North Richland Hills summers without some attention. Here’s what actually goes wrong with the Linear units we service, model line by model line.

• Linear LSO/OSCO slide operators: capacitor failure after 4-6 years. The start capacitor on Linear’s slide motor line takes a beating in Tarrant County heat, especially on west-facing gates that bake all afternoon. The symptom is a motor that hums but won’t move, or trips the breaker immediately. Some companies quote a full motor replacement for this. We replace the capacitor for a fraction of that.
• Linear Pro Access (LPA) swing arms: limit switch drift. The LPA-series swing arm uses mechanical limit switches that can slip a few degrees each year. The gate eventually stops a few inches short or slams the post. The fix is recalibrating the limits and tightening the cam set screw, but plenty of outfits misdiagnose this as a bad board. It’s rarely the board.
• Linear MegaCode access systems: receiver antenna corrosion. On the MegaCode receivers paired with Linear gates, the little antenna wire corrodes at the solder joint, especially after a few humid springs. Your remote works from ten feet but not from the street. We clean and re-solder it, or mount a weather-tight antenna, and range comes back.
• Linear APeX operators: stuck surge board after storms. The APeX line has a surge protection board that is supposed to sacrifice itself during a lightning strike. When it does, the whole opener goes dark. That’s the board doing its job. A replacement surge board is a thirty-minute fix; a lot of techs quote a full control board instead because they don’t stock the part. We keep them on the truck.
• Linear actuator arms on swing gates: worn bushings making a wake-the-neighbors noise. That grinding, groaning sound you hear when the gate moves? That’s the actuator arm bushings wearing out, usually from dust and grit off a limestone driveway. We press in new bushings and regrease the arm. Brand-new motor, same job, half the cost.

What ties all these together is that Linear failures are rarely “replace the whole unit” situations. Hal started fixing these in 2001 and he still believes you fix what’s broken and leave the rest alone.

Our Linear Gate Motor & Opener Process

1. 1
   You call, a person answers. 24 hours a day, no voicemail tree. We ask what the gate is doing, or not doing, and schedule a time that works. If it’s a gate stuck open or stuck shut, we treat it as urgent.
2. 2
   We diagnose on-site, in front of you. Hal or the crew member shows up, checks voltage at the board, tests the capacitor, inspects the arm or slide chain, and tells you exactly what’s failed and why. You don’t have to believe a diagnosis over the phone from a stranger; we’re standing in your driveway showing you.
3. 3
   Parts decision, stated plainly. If it needs a Linear OEM part, we use it. If there’s a quality aftermarket alternative that lasts as long and costs less, we tell you and let you choose. We never install an inferior part to pad a margin.
4. 4
   The repair happens right there. We carry common Linear capacitors, surge boards, limit switches, bushings, and receivers on the truck. If it’s a slide chain or full motor swap, we schedule the follow-up before we leave and it’s a one-visit job on the return.
5. 5
   We run the test cycle. Open, close, reverse, obstruction stop, remote range, keypad entry. If it doesn’t pass, it’s not done.
6. 6
   You get the 90-Day Done Right Promise in writing. One call and we’re back. No phone tag, no third-party warranty company, just Hal making it right.

Call (817) 241-4067 and we’ll set a time.

What Linear Gate Motor & Opener Costs in North Richland Hills

Here’s what you can expect on a Linear job in North Richland Hills:

• Capacitor replacement: $180 to $280, including the part and the service visit.
• Limit switch recalibration or replacement on an LPA swing arm: $140 to $250.
• Receiver antenna repair or remote programming: $120 to $200.
• Control board or surge board replacement (APeX): $300 to $500 depending on the board.
• Full Linear slide or swing motor replacement: $800 to $1,400 installed, depending on gate weight and what’s reusable.
• Complete new Linear gate opener package with motor, receiver, keypad, and safety edges: $1,500 to $3,000 for most residential setups in North Richland Hills.

What moves the price is gate weight, gate length, and whether the existing mount points and wiring are solid or need redoing. A gate that was installed wrong the first time costs more to fix than a straightforward motor swap, because we’ll redo the foundation rather than bolt a new motor to a post that’s leaning. You’ll know the number before we start, and it’s the number on the invoice when we leave. Call for a free estimate, no trip charge inside the county.

Why North Richland Hills Homeowners Call Gatewood Fence & Gate for Linear Work

We’re a local shop, Hal Gatewood has been fixing gates here since 2001, and the name on the business is the name on every invoice. That’s not a marketing hook; if we do sloppy work, you’ll see Hal at the Denny’s off Rufe Snow on Saturday morning. Most of our Linear customers in North Richland Hills came to us after a national outfit quoted a motor replacement for a $200 capacitor, or after a handyman wired an opener with, well, creative thinking.

We work on all the major brands, LiftMaster, Mighty Mule, Ghost Controls, DoorKing, so you’re not stranded if you also have a second gate with different equipment. Every job carries our 90-Day Done Right Promise. $40 off any repair over $200. Free second opinion on any written estimate. A permanent 10% discount for seniors and veterans. And when you call, a live person answers, because if a gate fails at midnight you shouldn’t have to leave a message.

FAQs