Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Irving
Gate motor and opener repair in Irving usually runs $185 to $420 for a service call and common motor repair, while full slide motor replacement on a Las Colinas driveway gate typically lands between $900 and $2,200 depending on the operator brand and access layout. We get to most Irving neighborhoods the same day you call, and Hal Gatewood has been fixing gates across DFW since 2001. If your gate is stuck, grinding, or won’t respond to the remote, call (817) 241-4067 and a live person answers, 24/7, not a voicemail.
Irving is not a one-size-fits-all gate town. Between the HOA-governed communities along Lake Carolyn Parkway and the 1960s brick ranch neighborhoods north of Highway 183, the gate hardware, soil conditions, and access layouts change block by block. We work all of it. A gate that binds in July because the clay under the post shrank two inches is a different job than a gate that won’t close because an HOA-specified operator fried its wiring in August heat. We know both.
Why Gatewood Fence & Gate Is Irving’s Preferred Gate Motor & Opener Company
Most of our Irving work comes from a homeowner whose gate company quoted one price on the phone and showed up with a different number on the invoice. Or whose “technician” swapped in a generic control board the HOA never approved. Hal Gatewood’s name is on the shop and on every job we do in Irving, and the 90-Day Done Right Promise is printed on the paperwork, not buried in fine print. If it’s not right, one call brings him back.
We are locally owned and owner-operated, not a franchise. When you call, you get a person who knows the difference between a gate off O’Connor Road where the post is rusted at grade level and a gate in Valley Ranch where the slide track has been pulled out of alignment by clay movement. Hal or one of his background-checked crew members shows up in a marked truck, walks the gate with you, and tells you what actually needs fixing versus what can ride a little longer.
That repair-first mindset matters in Irving. We fix gates other companies want to haul off and replace. Our crew welds on site, in your driveway, rather than dragging your gate to a shop across town. And because we’re coordinated out of our Dallas-Fort Worth office with crews serving Irving daily, we can usually get to you the day you call. Live answer, every time. That’s the whole point.
Our Gate Motor & Opener Services in Irving
We handle the full range of gate motor and opener work in Irving, from a dead remote on a side-yard pedestrian gate to a full commercial slide operator at a Las Colinas office campus. Below are the jobs we do most often for Irving homes and businesses.
Motor Repair
Most motor failures we see in Irving aren’t the motor itself. They’re the wiring, the limit switches, the capacitor, or the control board, and all of them are fixable. We diagnose on site and give you the number before any work starts. In Irving’s older brick ranch neighborhoods north of 183, we regularly find original 40-year-old operators with insulation cracked from decades of DFW heat. Sometimes the right fix is a $35 capacitor, not a $1,200 motor.
Slide Motor Installation
Sliding gates are everywhere in Las Colinas and along the MacArthur corridor, where side yards are too tight for a swing gate to clear a sidewalk or shared driveway. We install and service slide motors from DoorKing, Viking, Linear, and others. A slide motor installation in Irving typically runs $1,200 to $2,400 including the operator, rack and pinion or chain, safety photocells, and programming. We quote the full number before we order a single part.
Linear Motor Service
Linear motors, especially the classic actuator-arm style, are common on Irving’s 1990s and 2000s ornamental driveway gates. These units wear hard in our triple-digit summers because the gearbox seals dry out and the actuator arm gets stiff. We stock Linear parts locally for Irving jobs and can usually rebuild a worn unit for a third of what a full replacement costs. Fresh grease, new seals, and a realigned post fix more than half the Linear gates we see.
Intercom Integration
A lot of Irving HOA communities have entry intercoms or call boxes tied to the gate operator. When you replace a motor, the new unit has to talk to the old intercom, and that’s not automatic. We integrate new operators with existing HOA intercom, keypad, and telephone entry systems across Las Colinas and Valley Ranch. If the community CC&Rs dictate which operator brand can go in, we work within that spec and make the intercom relay fire correctly the first time.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Irving
We’re certified to service nine major gate brands, and on most Irving jobs that means DoorKing, Linear, and Viking. Those three show up constantly in Las Colinas HOA specs and older North Irving side gates. We keep common parts for them on the truck or at the shop, so a capacitor, limit switch, or remote doesn’t turn a one-day job into a week-long wait. If your HOA deed restrictions name a specific brand and model, we pull the CC&Rs and order exactly what’s approved. No off-spec substitutions that land a violation notice in your mailbox.
Common Gate Motor & Opener Problems We See in Irving Homes
- Posts pulled out of plumb by black clay. Irving sits on some of the most expansive black clay in the continental U.S. It shrinks inches in summer drought and swells after fall rain. That movement racks gate frames and binds motors until the operator stalls or the latch won’t catch. Post realignment is a routine part of nearly every service call we make in Irving.
- HOA-specified operators with heat-degraded wiring. Some operators specified by Las Colinas CC&Rs were not built for 105-degree DFW summers. Wire insulation cracks, connections loosen, and by mid-August the gate runs intermittently or throws a fault code. We replace the wiring with higher-temp rated insulation and retighten every connection in the panel.
- Shared driveway gates that stop holding open. On Irving lots with a shared driveway or a gate that also must allow pedestrians through, a misadjusted entrapment sensor or photocell will halt the gate entirely during busy hours. We set the safety edges, loop detectors, and hold-open timers so delivery trucks and foot traffic both get through without triggering a false reverse.
- Rusted post bases on 1960s to 1980s side gates. North Irving’s original brick ranch homes often have steel posts set in concrete that have been sitting in wet clay for 40 years. The post rusts through at grade level, the gate drops, and the motor drags it against the latch. We cut the post at the base, weld a fresh section, and sleeve it before the gate gets damaged beyond repair.
Pricing for Gate Motor & Opener in Irving, TX
A service call for gate motor and opener repair in Irving runs $185 to $420 for diagnostic work and common fixes like capacitors, limit switches, and control board resets. Slide motor replacement runs $1,200 to $2,400 depending on operator brand and whether we’re reusing the existing rack or installing new. Linear actuator repair typically falls $275 to $600 for seals, gearbox work, and realignment. Full gate motor installation with new post or concrete work goes up from there, and we quote every number in writing before we turn a wrench.
Standing offers for Irving customers: $40 off any repair over $200, no trip charge inside Dallas County, free second opinion on any written estimate, and 10% off for seniors and veterans, permanently. The price Hal writes down is the price you pay. Call (817) 241-4067 for a free estimate. You’ll get a live person.
We Also Serve Cities Near Irving
Our crews work Irving daily and also cover Coppell, Euless, Grapevine, and Bedford. If you’re on the edge of town or in a neighborhood that straddles a city line, call anyway. If we can’t get to you that day, we’ll tell you straight, not string you along.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Irving
Yes, many Las Colinas deed restrictions name specific operator brands, panel materials, and powder-coat colors, and using anything else can trigger an HOA violation notice. We pull the community CC&Rs or call the property management company before ordering parts, so the repair stays in compliance. Call (817) 241-4067 and tell us your community name; we’ll tell you what the paperwork allows.
It’s usually the clay first, then the motor second. Irving’s expansive black clay shifts post footings seasonally enough to rack the frame and bind the gate mid-travel. The motor then overdraws and trips its thermal protection. We check post plumb on every call before we touch the operator. Call (817) 241-4067 and we’ll diagnose it on site.
We stage the work so the gate never blocks access for long. On a shared driveway, we schedule the removal and install in one visit, block out a window with you and your neighbors, and keep the pedestrian path open throughout. The gate goes down for hours, not days. Call (817) 241-4067 to schedule around your shared access.
Yes, we wire new operators into existing HOA intercoms, telephone entry boxes, and keypads every week in Las Colinas and Valley Ranch. The relay voltage has to match, and some older systems need a buffer relay to fire correctly. We test the full cycle, gate and intercom together, before we leave. Call (817) 241-4067 and describe your setup.
Two reasons: Irving’s black clay moves posts enough to bind gates and strain motors year after year, and the DFW heat bakes wiring insulation and gearbox seals well past manufacturer-rated life. The same operator in sandy, stable soil might last a decade longer. In Irving we see the wear and we plan for it. Call (817) 241-4067 for a free assessment.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Irving since 2001.