Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Coppell
Gate parts and welding in Coppell usually means one of three things: a hinge post that has heaved out of square on black clay, a swing gate that drags on one corner, or an HOA that wants the repair done with the exact same tubular steel profile the street was built with in 1998. We handle all three. Gatewood Fence & Gate has been owner-operated since 2001, and our Gate Parts & Welding crew welds on site in your driveway, not back at some shop across the metroplex. When a gate on Kingsbridge Drive or Mockingbird Lane stops latching, you call (817) 241-4067 and a live person answers. Then Hal or one of his crew shows up with the right board, the right hinge, and a welder in the truck.
Why Gatewood Fence & Gate Is Coppell’s Preferred Gate Parts & Welding Company
We have spent over two decades pulling up to Coppell homes where the gate is the last thing the builder touched before the sod went down. That late-1990s ornamental iron work is now twenty-five to thirty years old. The original hardware was fine for the first fifteen years. It is not fine now. We know which hinge post is going to fail on which street because we have already fixed three of them on the same block. Coppell homeowners call us for Gate Installation in Coppell because we do not haul the gate off and surprise them with a replacement quote. We cut the bad section out, weld in the new steel, and match the finish so the HOA has nothing to fuss about.
The 90-Day Done Right Promise is in writing on every job. If the hinge sags or the weld fails within ninety days, one call brings us back. No runaround. No dispatch queue. We are the same Coppell gate repair crew that shows up next year when the other leaf starts dragging. Calls are answered around the clock by a real person, and Hal’s name is on every invoice because his name is on the shop. That is the kind of accountability you get from Gate Parts & Welding in Coppell when the company is not a faceless franchise.
Our Gate Parts & Welding Services in Coppell
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that is where we start. On Coppell’s black clay, the post itself tilts first, then the hinge gets pulled out of square and the leaf starts dragging on the brick paver apron. We cut the old hinge free, true up the post, weld on a new barrel or strap hinge rated for the gate’s weight, and shim the leaf so it swings free through the full arc. If the post has heaved more than a couple degrees, we go deeper, which is what the next section is about.
Post Replacement
Fix the panel without the post and you’ll fix it twice. Coppell’s Vertisol soil swells after spring rain and shrinks hard in the summer, and a gate post set too shallow gets pushed and pulled every season until it tilts. Our post replacement work means cutting the old post below grade, digging a new footing deeper than the frost line, setting the post in concrete with extra rebar, and welding the rails back so the gate hangs true. We do this on shared driveway gates, walk gates, and the double leaf entries that frame so many master-planned Coppell cul-de-sacs. The HOA only sees the finished post, which is the point.
Rail Repair
The horizontal rails take the abuse. On tubular steel gates from the 1990s, the lower rail is often the first to rust through, especially where the builder’s original weld did not get full paint coverage. We cut out the failed section, weld in period-correct 1.5-inch tubular steel to match the profile, and paint or powder-coat to blend. If the pickets are loose at the rail intersections, we weld those too. The gate ends up straighter than it was when we found it.
Custom Welding
Coppell HOAs are particular about what gets welded to what. We have matched rail profiles, picket spacing, and even original powder-coat textures on gates throughout the city. Whether you need a new hinge boss welded onto a custom iron gate, a broken scroll repaired on a decorative driveway entry, or a steel frame built for a new pedestrian gate, we do the work on site. The gate never leaves your property. That matters when the gate is load-bearing for the fence line and your HOA has already approved the design.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Coppell
We are certified for Coppell Gate Motor & Opener service on Linear, LiftMaster, FAAC, BFT, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. On Coppell job sites we keep Linear, Viking, and Ghost Controls parts on the truck most often, because those brands showed up on thousands of Coppell driveways in the late 1990s and early 2000s. When a 2001 Linear swing-gate actuator board dies on one house, we usually hear from two neighbors within a month. Stocking the right board ahead of time means you are not waiting three days for a part while your driveway gate sits half open. That local parts knowledge is something a generic gate repair franchise cannot fake.
Common Gate Parts & Welding Problems We See in Coppell Homes
- Heaved hinge posts on expansive black clay. Coppell’s Vertisol soil swells in wet months and shrinks hard in summer, tilting posts seasonally until the gate drags and the operator arm binds. Welding alone will not fix a post that has shifted; the footing has to be redone.
- Shared driveway double gates losing sync on narrow setbacks. So many Coppell lots have 12- to 14-foot driveway aprons, so the double leaf arrangement is common. One leaf’s rack-and-pinion wears unevenly, the operator overloads, and the gate stops mid-travel.
- Twenty-year-old OEM swing-gate boards failing in clusters. Late-1990s Coppell subdivisions were built with identical operators block by block. When one control board or capacitor goes, the neighbors running the same unit are usually weeks behind.
- UV-cracked nylon rollers and photo-eye housings. Coppell summers top 100°F, and that sun bakes the plastic parts on automated gates. Cracked rollers make the gate grind and bind; cracked photo-eye housings trigger false obstruction errors.
Pricing for Gate Parts & Welding in Coppell, TX
Here is what we charge in Coppell. A hinge replacement on a standard ornamental iron swing gate runs $180 to $320, including welding and touch-up paint. Gate post replacement, with a new concrete footing set below grade, runs $450 to $850 depending on whether it is a walk post or a heavier double-drive post. Custom welding repair, like a broken scroll or a rusted rail section, runs $220 to $600 based on length and access. The price is quoted and agreed before any work starts. No trip charge inside the county. $40 off any repair over $200, and seniors and veterans get 10% off permanently. Call (817) 241-4067 for a free estimate; we will give you a written number before we strike an arc.
We Also Serve Cities Near Coppell
We run the same gate parts and welding crews up to Grapevine, Flower Mound, Euless, and Southlake. Same HOA-heavy neighborhoods, same aging ornamental iron, same black clay. If you live just outside Coppell, call and ask how soon we can get to your driveway.
Serving Coppell, TX - Our Local Coverage Area
We’re based in the Coppell area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Coppell
Coppell’s black clay soil swells after spring rain and shrinks in summer, and a post set any shallower than about two and a half feet gets worked loose season after season. Welding alone will not fix a tilting post; the footing has to be cut out, re-dug, and re-set. We do that on a regular basis, and the weld is part of the job, not the whole job. Call (817) 241-4067 to get your gate swinging true again.
Yes. We keep period-correct 1.5-inch tubular steel profiles in stock specifically for Coppell’s late-1990s HOA subdivisions, and we match the original finish before we leave. If your HOA needs documentation of the material or finish spec, we will put it in writing. Call (817) 241-4067 and tell us your street and your HOA’s requirements.
On narrow Coppell driveway setbacks, a shared double gate or slide gate with Gate Access Control - Coppell often loses sync when one leaf’s rack-and-pinion wears unevenly or the operator overloads and stops mid-travel. The fix usually means re-sync of the operator and replacement of the worn gear or roller, and we can do it without closing the driveway for more than an hour or two. Call (817) 241-4067 for a free estimate.
It is. Late-1990s and early-2000s Coppell subdivisions were often built with identical OEM swing-gate operators community-wide, so control boards and capacitors fail in clusters at the same age. We stock Legacy/Linear and early LiftMaster boards specifically for these Coppell HOA blocks. Call (817) 241-4067 and tell us the operator model; we will bring the right board.
Yes. We stage the work one side at a time and keep the pedestrian gate operational throughout, which matters when your kids are walking to the school bus and you do not want the whole entryway blocked off. On shared driveways we coordinate with both neighbors before we start. Call (817) 241-4067 to schedule a free estimate.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Coppell since 2001.