Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Bedford
A gate motor and opener repair in Bedford usually runs $145 to $385, and most failures we see trace back to one thing: the Blackland Prairie clay under your hinge post has moved again. We know Bedford’s lots, its fence lines, and the way its gates lean after a wet spring. Gatewood Fence & Gate is owner-operated, the phone is answered by a live person around the clock, and we show up when we say we will. Call (817) 241-4067 for a straight answer and a free estimate.
Why Gatewood Fence & Gate Is Bedford’s Preferred Gate Motor & Opener Company
Hal Gatewood has been fixing gates since 2001, and his name is on the shop and on every invoice. That matters in a landlocked mid-cities suburb like Bedford, where the houses were built between 1965 and 1995 and the gate hardware is often older than the people answering the phone at a national outfit. We do not dispatch a stranger from three states away. The person who shows up lives in the metro, knows Harwood Road from Forest Ridge Drive, and has seen your exact gate failure dozens of times.
Bedford homeowners tell us the same story: a gate that worked fine in March is binding and faulting by July. We know why. The soil underneath is expansive clay that swells with spring rain and shrinks in summer drought. That seasonal heave tilts hinge posts, and a tilted post makes a motor work against the full weight of a bound panel. We check the footing before we quote a control board, because replacing the board without fixing the post just means you will call us again in six months. Our 90-Day Done Right Promise is in writing on every job, not in fine print.
Our Gate Motor & Opener Services in Bedford
Motor Installation
A new gate motor installation in Bedford typically runs $950 to $2,400 depending on the operator brand and the condition of your existing posts. We do not sell you a motor without looking at the gate first. Around Bedford, if the hinge post has tilted past an inch or two out of plumb, the honest answer is to fix the post before hanging a motor on it. We install and service LiftMaster, Linear, Viking, Ghost Controls, DoorKing, FAAC, BFT, Elite, and Mighty Mule. Hal or his crew handles the wiring, the travel limits, and the safety edges, and every installation gets the 90-Day Done Right Promise in writing.
Motor Repair
Motor repair in Bedford is where we spend most of our days. A control board replacement usually runs $185 to $420, a drive gear or limit switch repair $120 to $310, and full motor rebuilds start around $400. We are a repair-first shop. If a control board on a 1980s LiftMaster is still available and worth replacing, we will tell you that, rather than quoting a whole new operator because it is easier for us. On-site welding means we can repair a cracked arm or a bent bracket in your driveway instead of hauling your gate to a shop across town.
Linear Motor
Linear is one of the most common actuator-style operators on Bedford’s older residential swing gates. These are the rod-shaped motors that push and pull the gate leaf directly. They fail differently here than they do in Dallas or Fort Worth: the clay movement bends the mounting brackets and puts axial load on the actuator rod until the seals wear, water gets in, and the motor shorts. Common Linear repairs in Bedford run $150 to $360 for limit switches, capacitors, and control board work. We stock Linear parts locally and can usually have your gate running the same visit.
Slide Motor
Slide gates are rarer in Bedford than swing gates, but they show up on some of the older homes east of 121 and on a few commercial driveways along Harwood. Slide motors in Bedford run $1,100 to $2,600 installed. The local failure mode is different: when the clay heaves under the track, the gate wheels drag or bind, and the motor draws high current until the control board fries or the gearbox strips. Before we install a slide motor, we check the track level and the footing. If the track has moved, we say so and price the repair honestly.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Bedford
We are certified to service nine major gate brands, and for Bedford customers we keep parts on the truck for the ones we see most: Linear, Viking, Ghost Controls, and DoorKing. If you have a LiftMaster operator from the original 1980s or 1990s build-out, we can tell you honestly whether the board is still available or whether retrofit is the cheaper path. Fast turnaround matters when your gate is stuck open on Brown Trail or your car is trapped inside on Woodbine Drive. We do not make you wait a week for a part that is sitting on our shelf.
Common Gate Motor & Opener Problems We See in Bedford Homes
- Thermal overload trips every spring. The post footing has tilted from seasonal clay heave, the top hinge binds, and the motor fights the weight of the whole panel. Fixing the post is step one; resetting the limits without fixing the post is a short patch, not a repair.
- Control board failures on legacy operators. Bedford has hundreds of 1970s to 1990s installations with original boards that were never designed for North Texas heat. A board that bakes on a 100°F afternoon can fail intermittently for weeks before it dies for good.
- Sheared hinge bolts after spring storms. When a thunderstorm catches a large wood gate leaf like a sail, the hinge bolts snap or bend. We get those calls most after the April and May storm fronts push through Bedford, and the operator is usually still running against a twisted leaf, stripping its own gears.
- Missing or obsolete safety photocells. A lot of Bedford’s original gates went in before modern entrapment protection was code. If your opener reverses without an obstruction or fails to reverse at all, the photocells or the loop detector are usually dead, and that is a safety issue, not a convenience one.
Pricing for Gate Motor & Opener in Bedford, TX
We Also Serve Cities Near Bedford
Our Gate Motor & Opener team covers Bedford and the surrounding mid-cities. If you are in Colleyville, Euless, Hurst, or North Richland Hills, we handle gate motor repair and installation there too. The same live person answers the phone, the same no-trip-charge policy applies inside the county, and the same Bedford crew knows the soil, the housing stock, and the gate failures across the whole HEB corridor.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Bedford
The Blackland Prairie clay under your hinge post swells with spring rain and tilts the post, which makes the gate bind at the top hinge and overloads the motor. The operator stops on its thermal protection because it is working against a bound panel, not because the motor is bad. The fix is to re-plumb the hinge post in a deeper, wider footing and then reset the travel limits. Call (817) 241-4067 for a free estimate and we will check the post before we touch the motor.
Yes, and we do it regularly on Bedford’s original installations. Retrofit photocells and a loop detector usually run $350 to $700 installed, depending on wiring access and whether the existing operator has the right input terminals. Older LiftMaster and Viking boards sometimes need a relay interface, which adds a little to the job. Call (817) 241-4067 and we will tell you exactly what your operator can take.
A gate sags in the hinge post, not in the middle. If the post is still sound, we can re-hang the gate leaf, correct the sag, and rebuild the motor. If the post is rotted or tilted beyond repair, the honest fix is a new post in a larger footing, and often that is cheaper than repeatedly rebuilding the operator. Either way, we will show you the post before we quote the motor. Call (817) 241-4067 to have Hal look at it.
If your operator was installed before 2000 and has never been retrofitted, it almost certainly does not meet current UL 325 entrapment standards. Missing photocells, no reversing mechanism, and no loop detector are the telltale signs. This is a safety matter, not a luxury upgrade. A trained professional should test the reversing sensitivity and the photocell alignment; do not wire safety devices yourself if you are not sure. Call (817) 241-4067 and we will test the system and give you a straight answer.
Yes, especially on Bedford homes where the gate is the only way a car gets in or out. North Texas sees hard freezes and spring storms that knock out power for hours at a time, and a gate without battery backup means you are manually releasing the operator in the rain. A battery backup system for a Bedford gate typically runs $250 to $500 installed. Call (817) 241-4067 and we will tell you if your operator can take one.
If your gate motor is struggling in Bedford, call Gatewood Fence & Gate at (817) 241-4067. A live person answers, the estimate is free, and the price we quote is the price you pay. Hal Gatewood has been at this since 2001, and his name is on the shop, not a franchise agreement.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Bedford since 2001.