Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Installation for North Richland Hills Homeowners
A new gate for your property should last 20 years or more, which means North Richland Hills Gate Installation matters just as much as the gate itself. We’ve been setting gates in this town since 2001, and we still see installations from other companies where the post was set shallow, the hinges were undersized, or the gate was hung out of level from day one. Hal Gatewood does the work with his own crew, welds on site, and backs every installation with the 90-Day Done Right Promise in writing. If you’re planning a gate, call (817) 241-4067 and you’ll get Hal himself, not a recording.
What Our Gate Installation Service Includes
Every gate we install in North Richland Hills starts with the same thing: a straight conversation about what the gate needs to do. That means how it opens, what it weighs, who uses it, and what the ground underneath is actually doing. From there we quote one price up front, in writing, and nothing changes at the door. Here’s what each type of installation involves.
Driveway Gate
A Driveway Gate is the one your car goes through, and in North Richland Hills it’s usually the first thing a visitor sees. We set the hinge posts in concrete below frost line, size the frame to the opening, and hang the gate so it swings or slides without dragging. We also account for the slope of your driveway, because a gate set on a grade that wasn’t measured will bind and sag within two years. Most driveway gate installations here run a full day from layout to final walkthrough.
Pedestrian Gate
A Pedestrian Gate is the smaller walk-through gate beside the driveway or into a side yard. It gets more cycles per day than any other gate on the property, so we build it to handle repeated use. We set posts in concrete, weld the frame if it’s steel, and adjust the hinges so the gate closes square and latches without being slammed. If you’ve had a wooden pedestrian gate go soft, we’ll show you why before we replace it.
Sliding Gate
A sliding gate rolls horizontally instead of swinging, and it’s the right call for driveways with limited swing room or a steep approach. We install the track, set the receiver post, and align the rollers so the gate travels without wobble. In North Richland Hills we see a lot of sliding gates that were installed with track too light for the gate weight, and the result is a gate that binds halfway. We size the hardware to the actual gate, not to a guess.
Swing Gate
A swing gate pivots on hinge posts, and it’s still the most common gate style in North Richland Hills for good reason: fewer moving parts and quieter operation. The key to a swing gate that lasts is the hinge post. We set our posts deeper than code minimums and use heavier wall posts than most of what we see out there. A sagging swing gate is almost always a post that shifted, not a hinge that wore out, and that’s where we start.
Double Gate
A double gate is two leaves that meet in the middle, used for wide driveway openings where a single swinging leaf would be too heavy or too slow. We build both leaves to match, set three posts instead of two, and add a center drop rod so the closed gate doesn’t flap in the wind. We also check the alignment at the middle so the two leaves meet evenly, which is the first thing that goes wrong on a badly installed double gate.
Security Gate
A security gate is designed to stop someone who doesn’t want to be stopped, not just mark a property line. We build these with heavier steel, weld the frame continuously, and add the operator hardware needed for controlled access. In North Richland Hills, security gates often get paired with an access control system, and we handle that wiring on site so you’re not coordinating three different contractors. The safety edges and photo eyes get tested before we leave, every time.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Installation
We install and service Ghost Controls, DoorKing, Elite, and Mighty Mule operators regularly, and we keep OEM parts for all four on the truck. Ghost Controls is what we see most often on residential swing gates in North Richland Hills, and we’ve gotten know their battery and solar configurations well enough that we can usually diagnose a problem in the driveway before checking the manual. DoorKing is the workhorse for sliding gates and light commercial work, and we stock the limit switches and receiver boards for the current models.
Elite and Mighty Mule show up on a lot of ranch gates and acreage properties around North Richland Hills, and we handle both the install and the wiring for them. The thing about any operator is that a gate that was hung poorly will destroy a good opener within a year or two. We fix the gate first, then mount the operator, then test it for full cycles. Whether you already have one of these brands or you’re starting from scratch, we’ll build around what you have, not sell you a swap.
Signs You Need Gate Installation Right Now
- The gate drags on the ground or won’t close all the way. This means the post has moved or the hinges have worn, and patching it only buys months. A gate that can’t close is a gate that isn’t doing its job, and it will only get worse.
- You can see daylight between the post and the ground where it was set. That post was poured shallow or the concrete has cracked, and the whole gate is now leaning on the hardware. Rehanging a gate on a moving post wastes the new gate, so the post gets replaced first.
- The gate has been welded back together more than once. A cracked weld means the frame is flexing, which means the gate was undersized for the opening or the post is still moving. New steel on a compromised frame is money down the same hole.
- You’re propping the gate open with a rock or a bungee cord. If the gate won’t stay put on its own hardware, something has failed. It’s usually the post, sometimes the hinges, and occasionally the ground under the post. Either way, the fix is installation, not a larger rock.
- The opener is working but the gate isn’t. When the motor is fine and the gate still won’t travel, the gate itself is the problem. Replacing an operator before the gate is fixed just burns up another motor.
Our Gate Installation Process - Step by Step
- 1
Measure and assess the site. We come to the property and measure the opening, check the slope, and note what the soil looks like around the post locations. North Richland Hills has clay that shifts with the wet and dry seasons, so post depth matters more here than in some other parts of the Metroplex.
- 2
Price it in writing. You get one price for the entire job: gate, posts, hardware, welding, operators if you’re adding one, and cleanup. The number we give you before the work is the number on the invoice when we leave. No trip charge inside the county.
- 3
Build or order the gate, then set the posts. If we’re welding a custom gate, it gets built in our shop in North Richland Hills. Posts go in below frost line in concrete, and we don’t set a post and hang a gate in the same afternoon; the concrete needs to cure.
- 4
Hang the gate and mount the operator. We hang the gate level, adjust the hinges or rollers, and if there’s an automated operator, we mount it and run the power. Every gate gets cycled open and closed repeatedly while we watch for travel issues.
- 5
Walk it with you and back it in writing. You’ll see the gate open and close, and we’ll show you how to disengage the opener if you lose power. Every job gets the 90-Day Done Right Promise in writing: if it’s not done right, Hal comes back and makes it right. No runaround.
How Much Does Gate Installation Cost in North Richland Hills?
A single swing driveway gate in North Richland Hills typically runs $1,800 to $4,500, depending on the gate material, width, and whether we’re adding an operator, so Gate Installation pricing varies by project. A double gate for a wide drive starts around $3,000 and can go to $7,000 or more with automation and access control. Pedestrian gates run $600 to $1,800, and sliding gates fall between $2,500 and $6,500, with the price driven mostly by track length and gate weight.
What moves the price: the width of the opening, whether the gate is steel or aluminum, whether we’re cutting and welding a custom frame or installing a prefabricated gate, and whether there’s power to the gate location. Operator add-ons for Ghost Controls, DoorKing, Elite, or Mighty Mule typically run $700 to $2,500 installed, including the safety edges and photo eyes. The way to avoid overpaying is to get a price that’s written down and doesn’t change at the door, and to make sure the post work is included. We’ve seen quotes from other companies in North Richland Hills that excluded the concrete and then surprised the homeowner with a change order. Our estimate includes everything: posts, concrete, hardware, welding, and cleanup. Estimates are free, and we’ll give you a second opinion on any written quote you already have.
Gate Installation Near North Richland Hills - Our Service Area
We install gates across North Richland Hills and the surrounding cities including Fort Worth, Southlake, Colleyville, Hurst, Bedford, Keller, Euless, and Grapevine. If you’re in one of those towns, we’re usually on site within a day or two of the estimate. We’ve put gates on properties from Flower Mound to Arlington, and the same crew that shows up in North Richland Hills is the crew that will show up at your place. See more about Gate Installation in Fort Worth or Gate Installation in Southlake if you’re on that side of the county.
Serving North Richland Hills, TX - Our Local Coverage Area
We’re based in the North Richland Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Installation in North Richland Hills
Gate installation means setting hinge or track posts in concrete, hanging the gate on those posts, and adding any hardware or operators needed to open and close it. A proper installation includes leveling, swing or slide adjustment, and testing under real use. In North Richland Hills, our installations always include the post work, because that’s the part most installs get wrong.
Most single driveway gate installations in North Richland Hills are done in one day, with the concrete given time to cure before the gate is hung. A custom double gate or a sliding gate with a power run may take two days. We’ll tell you the schedule before we start, and we won’t leave the job half-finished. Call (817) 241-4067 if you have a specific deadline.
A typical driveway gate installation here runs $1,800 to $4,500, with double gates and automated sliding gates going higher. The best way to get a firm number is to call us for a free estimate: we measure the opening, check your property, and quote one price in writing. That price covers the gate, posts, concrete, hardware, and cleanup, with no change orders at the door.
We install and service Ghost Controls, DoorKing, Elite, and Mighty Mule operators, and we keep OEM parts for all four on the truck. If you already have one of these brands on a gate that’s failing, we’ll tell you honestly whether the gate is the problem or the operator is. Fix the gate first, save the motor, that’s how we work.
If your gate is stuck open or won’t close and you need it secured, call us at (817) 241-4067. We answer around the clock and we’ll tell you over the phone what we can do and when we can get there. Emergency service in North Richland Hills is something we take seriously, because a gate that won’t close is a security problem, not a cosmetic one.
Every installation from Gatewood Fence & Gate carries the 90-Day Done Right Promise in writing: if it’s not done right, we make it right, and one call brings Hal back. Beyond that, the gate and hardware manufacturers carry their own warranties, and we handle the paperwork for you. We’re local, so warranty follow-up isn’t a phone tree, it’s a visit.
Clear the area around the gate opening of anything that would block a truck or a welder, and let us know if there are sprinkler lines, low-voltage lighting, or underground utilities near the post locations. We’ll mark and check before we dig. If you have pets, keep them inside while we’re working, because open gates and curious dogs don’t mix.
Schedule Your Gate Installation Service in North Richland Hills Today
Call (817) 241-4067 for a free estimate on gate installation in North Richland Hills. You’ll talk to a live person, you’ll get a written price before the work starts, and the name on the invoice will be Hal Gatewood, the same name that’s been on the shop since 2001. We’ll show up when we say we will and we’ll leave you a gate that operates right. No runaround, no change orders, no surprises. If you’d rather, you can start with our home page to see the full range of what we do.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving North Richland Hills since 2001.