Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Watauga
Gate repair in Watauga usually costs between $160 and $540 depending on whether we’re dealing with a sagging hinge, a heaved post, or a dead operator. Most jobs are done the same day we roll up. If you’re standing in a driveway off Rufe Snow Drive with a gate that won’t latch or an opener that quit overnight, you want someone who knows why Watauga gates fail the way they do. You want Hal Gatewood on the other end of the line at (817) 241-4067. We’ve been fixing gates in Tarrant County since 2001, and the phone rings to a live person, not a queue.
Why Gatewood Fence & Gate Is Watauga’s Preferred Gate Repair Company
Hal Gatewood has owned and operated this company since 2001, and his name is on the shop. It’s also on every invoice. That’s not a marketing line. You can look up the license number, you can drive to the shop, and you can talk to the same person who quoted the job. Watauga homeowners have called us from Haltom Road to Watauga Road and points between, and we’ve earned a strong local reputation by fixing what other companies want to haul off and replace. We weld on site in your driveway, so your gate doesn’t leave your yard unless it has to.
Our crew reaches most Watauga neighborhoods the same day you call. Background-checked, uniformed, and driving a marked truck. Every job gets the 90-Day Done Right Promise in writing. If it’s not right, one call brings us back, no runaround. That’s how Hal has done it for over two decades.
Our Gate Repair Services in Watauga
Hinge & Post Repair
This is the bread-and-butter of gate work in Watauga, and it’s the one thing most national outfits get wrong. A sagging gate rarely starts at the center of the panel. It starts at the hinge post, which was likely set in minimal concrete back when Nixon was in office and has been slowly heaving out of level in the black clay ever since. We reset the post with a deeper footing that punches below the active clay zone, then rebuild the hinge connection with hardware rated for the weight. In Watauga, hinge and post repair runs $180 to $390 on average, depending on whether we’re replacing one hinge or resetting the entire post. $40 off any repair over $200 in Watauga, plus no trip charge inside the county.
Gate Realignment
Watauga’s wet spring and furnace summer don’t just wreck posts. They twist the gate frame itself. A wood gate that soaked up rain, then baked in 102-degree heat, will warp out of square. We square the frame, add steel sag correction where needed, and get the latch engaging again. On 1980s-era homes between Rufe Snow and Denton Highway, gate realignment usually runs $140 to $280. We quote the price before any work starts and you approve it before we touch a single hinge.
Electric Gate Repair
If your electric gate in Watauga stopped responding to the remote, there’s a good chance it’s a failed control board or a photo-eye knocked out of alignment. We service LiftMaster, BFT, Linear, and most other major brands, and we keep common parts on the truck so we’re not waiting on a supplier in Fort Worth while your driveway stays open all week. Electric gate repair in Watauga typically runs $220 to $540, with the control board being the most common higher-ticket item. We’ll tell you plainly if the operator’s worth saving or if a retrofit makes more sense.
Weld & Rust Repair
Tubular steel gates from the 1980s rust from the inside out, and the bottom rail where water collects is usually the first to go. We grind out the rust, weld the section solid, and treat it so it holds through Watauga’s wet-dry cycles. If you have a steel gate with a rusted-through bottom hinge mount, call us before you assume it’s landfill-bound. We fix what’s fixable.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Watauga
We’re certified to work on nine major gate brands, and around Watauga we see a lot of LiftMaster, BFT, and Linear operators going strong after two decades, plus Viking units on some of the heavier steel gates. We keep common parts for these brands on the truck, so a repair in Watauga doesn’t mean three trips across the Metroplex. If you’ve got a Ghost Controls board acting up or a Mighty Mule that won’t hold a position, we can usually source the part same week. Call (817) 241-4067 and tell us what you’re running. A person will answer.
Common Gate Repair Problems We See in Watauga Homes
- Clay-driven post heave: The expansive black clay under Watauga shrinks in the long dry summers, then swells during spring rains. Over decades, this cycle rocks gate posts loose and out of plumb, making the gate drag on one side and gap a half inch on the other. In 1970s and 1980s subdivisions like Whispering Hills and Wintergreen, almost every original post is now out of level.
- Shallow original footings: Most of Watauga’s tract homes were built between 1972 and 1995, and gate posts went in with a couple of bags of concrete and a hope. After 30 to 50 years, those footings have failed. Re-hanging the gate without resetting the post means fixing it twice.
- Ice-storm hinge damage: Watauga sits in the Fort Worth ice-storm corridor. When a hard freeze hits, water inside iron hinges expands and cracks them. Water-saturated wood gates split along the grain. We see a wave of these calls after every freeze event.
- Obsolete operator boards: Older LiftMaster and Linear boards in Watauga homes are now 15 to 25 years old. When they fail, they fail dead. We’ll tell you honestly if a new board is the right call or whether the whole operator has reached the point where replacement is cheaper than chasing parts.
Pricing for Gate Repair in Watauga, TX
Here’s what we charge in Watauga, in plain numbers, before we step foot in your yard:
- Gate realignment: $140 to $280
- Hinge replacement without post reset: $160 to $240
- Hinge and post repair with post reset: $280 to $540
- Electric gate repair, including control board replacement: $220 to $540
- Weld and rust repair on tubular steel gates: $180 to $380
We quote the full price over the phone or on site before work begins. It’s agreed in writing. It doesn’t change at the door. You’ll never sign off on a repair, then get a call saying the “parts came in higher.” A free estimate means exactly that. Pricing in Watauga is comparable to North Richland Hills and Colleyville, but clay heave here makes post work more common, so you’ll likely need that depth of repair more than your cousin in a sandier part of the county does.
We Also Serve Cities Near Watauga
Watauga’s our focus on this page, but if you’re just across the city line in North Richland Hills, Fort Worth, Southlake, or Colleyville, the same local crew covers you. No third-party call center. The person you talk to is tied to the shop. Check out our Gate Repair service page to see the full scope of what we do.
Serving Watauga, TX - Our Local Coverage Area
We’re based in the Watauga area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Watauga
Nine times out of ten, it’s the post. Watauga’s black clay shrinks in the summer heat and the whole post drops or tilts, dragging the gate with it. Replacing hinges won’t fix the underlying problem unless the post is reset below the active clay zone. We’ll verify it on site. Call (817) 241-4067 for a free estimate.
Yes, if it’s reset to the proper depth. A properly installed footing that reaches below the active clay zone won’t move with seasonal expansion and contraction the way a shallow post does. Hal has set posts in Watauga clay for years and knows how deep to go. And it’s covered under the 90-Day Done Right Promise in writing.
Blowing a board repeatedly usually means something upstream is killing it, like a bad transformer, a shorted limit switch, or water getting into the cabinet. Retrofit is realistic on older LiftMaster units if the motor and gear train are still sound. If the gears are stripped and the board is bad, replacement is the cheaper long-term answer. Hal will tell you which way to go. Call (817) 241-4067 for a straight answer.
In most cases, yes. We cut back to clean metal, weld a new piece in, grind it flat, and coat it. If the frame rails are too far gone on multiple sides, we’ll say so. But we don’t replace what we can repair. That’s the point of being welding shop first and a gate company second.
Most of those gates are fixable if the wood is structurally sound. The problem you’re describing is the post, not the gate. Once the post is reset, we square the frame and add sag correction, and it’ll hold through the next wet-dry cycle. If the wood itself is rotten or splitting through the rails, then a new gate is the cheaper answer. We’ll show you both numbers before any work is approved.
Call for Gate Repair in Watauga, TX
If your gate is sagging, dragging, sticking, or dead, call (817) 241-4067 for a free estimate. Hal Gatewood’s crew will show up when promised, quote the job before work starts, and stand behind it for 90 days in writing. No trip charge inside Tarrant County. $40 off any repair over $200. A permanent 10% discount for seniors and veterans. And a live person answers every call, day or night. That’s how a local owner-operated gate company in Watauga does it.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Watauga since 2001.